Кофемашина Siemens TK 53009 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
20
en
Changing volume
dispensed
The pre-set quantities for dispensing button
3
E
(approx. 40ml) and dispensing button
4
F
(approx. 125 ml) can be changed.
●
Press and hold the coffee dispensing
button
3
E
or
4
F
until the desired
volume of coffee has been delivered
(range approx. 30 – 220 ml).
i
The quantity can be changed again at
any time. By pressing “Reset”, the factory
settings are restored.
Reset:
The appliance must be ready for
use.
●
Pull out trays
17
and
18
. Press and hold
dispensing buttons
3
E
and
4
F
at the
same time for at least 5 seconds.
●
The LEDs
7a, b, c
and
d
(
H
,
I
,
S
,
J
)
flash briefly as confirmation.
●
Reinsert trays
17
and
18
.
The standard factory settings have now
been reactivated.
Preparing hot water
The appliance must be ready for use.
This function allows water to be heated for
a cup of tea, for example.
¡
Risk of burns
The nozzle gets very hot. Do not touch the
metal parts.
●
Place an appropriate cup under the
nozzle
8
.
●
Push the sleeve on the nozzle
8
all the
way
down
.
●
Turn the dial
6
to
g
/
h
.
¡
Risk of scalding
When the dial is set to
g
/
h
, the nozzle
may sputter a little. Do not touch the nozzle
8
or point it at anyone.
●
End the process by turning the dial
6
back to “
O
”.
Steam for foaming milk
The appliance must be ready for use. You
can foam the milk first and add the coffee
on top, or foam the milk separately and
pour it into the coffee.
¡
Risk of burns
The nozzle gets very hot. Do not touch the
metal parts.
●
Push the sleeve on the nozzle
8
all the
way down.
●
Fill the cup approximately 1/3 full of milk.
●
Press the steam button
h
. The LED will
start to flash.
i
The appliance will heat up for approx.
20 seconds.
●
Immerse the nozzle
8
deep into the milk,
but do not let it touch the bottom of the
cup.
●
As soon as the LED
J
lights up, turn the
rotary button
6
to
g
/
h
.
¡
Risk of scalding
When the dial
6
is set to
g
/
h
, the nozzle
8
may sputter. Escaping steam is very hot
and may cause liquids to sputter. Do not
touch the nozzle
8
or point it at anyone.
●
Rotate the cup slowly until the milk is fully
foamed.
●
End the process by turning the dial
6
back to “
O
”.
i
To foam more milk, press the steam
button
h
again and repeat the whole
process.
Note:
When the nozzle
8
has cooled down,
clean immediately. Dried residue is difficult
to remove.
Tip:
If possible, use cold low-fat (1,5 % fat)
milk.
