Кофемашина Bosch TES 50129 RW - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
Robert Bosch Hausgeräte GmbH
12
en
Important:
If a water filter is used (special
accessory order no. 461732), proceed as
follows, see „Water filter“ on page 10.
Note:
If no button is pressed within 90 sec-
onds, the appliance switches to stand-by
mode without saving the new settings. In
this case, the previously saved water hard-
ness setting is retained.
Automatic switch-off
Here you can set the period of time after
which the appliance should switch off au-
tomatically following the last drink prepa-
ration. A time between 15 minutes and 4
hours can be set. The default time is 1 hour,
but this can be shortened to save energy.
1. Turn the rotary
knob (13) to position
2. Press and hold buttons
B
(11) and
A
(12) simultaneously for at least 5 sec-
onds. The time after which the appliance
should switch off is indicated by the
number of LEDs that now light up.
3. Now press the start button (10) repeat-
edly until the required number of LEDs
light up to indicate the switch-off time:
D
= 15 minutes
D
and
E
= 30 minutes
D
,
E
and
F
= 45 minutes
D
,
E
,
F
and
G
= 1 hour
D
,
E
,
F
,
G
and
H
= 2 hours
D
,
E
,
F
,
G
,
H
and
I
= 4 hours
4. Press and hold the start button (10) for
at least 5 seconds. The set number of
LEDs will light up to indicate that the
selected switch-off time has been saved
successfully.
Note:
If no button is pressed within 90 sec-
onds, the appliance switches to stand-by
mode without saving the new settings. In
this case, the previously saved switch-off
time is retained.
Setting the brewing temperature
The brewing temperature can also be set.
1. Turn the rotary
knob (13) to position
2. Press and hold buttons
B
(11) and
A
(12) for at least 5 seconds. The set
brewing temperature is indicated by the
number of LEDs that now light up.
3. Now press the start button (10) repeat-
edly until the required number of LEDs
light up to indicate the temperature:
LED
D
= low
LED
D
and
E
= medium
LED
D
,
E
,and
F
= high
4. Press and hold the start button (10) for
at least 5 seconds. The set number of
LEDs will light up to indicate that the
selected temperature has been saved
successfully.
Note:
If no button is pressed within 90
seconds, the appliance switches to stand-
by mode without saving the new settings.
In this case, the previously saved brewing
temperature setting is retained.
Adjusting the grind settings
The selector (3) for grind setting adjusts the
grind settings from coarse to fine.
Caution
Adjust the grinding unit only while it is run-
ning! Otherwise the appliance may be dam-
aged. Do not reach into the grinding unit.
TES501_Heft1_RW.indb 12
14.09.2011 16:10:24
