Ryobi RiD1801M - Инструкция по эксплуатации - Страница 3

English

1

EN

FR

DE

ES

IT

NL

PT

DA

SV

FI

NO

RU

PL

CS

HU

RO

LV

LT

ET

HR

SL

SK

BG

UK

TR

EL

Safety, performance, and dependability have been given 
top priority in the design of your impact driver.

INTENDED USE

The impact driver is intended to be used only by adults who 
have read and understood the instructions and warnings in 
this manual, and can be considered responsible for their 
actions.
The product is intended for fastening and removing screws 
and bolts.
The product is intended for consumer use only. 
Do not use the product for any other purpose. Use of the 
product for operations different from intended could result 
in a hazardous situation.

 WARNING

Read all safety warnings, instructions, illustrations 
and specifications provided with this power tool. 

Failure to follow all instructions listed below may result in 
electric shock, 

fi

 re and/or serious injury.

Save all warnings and instructions for future reference.

IMPACT DRIVER SAFETY WARNINGS

■

Hold the power tool by insulated gripping surfaces, 
when performing an operation where the fastener 
may contact hidden wiring.

 Fasteners contacting a 

“live” wire may make exposed metal parts of the power 
tool “live” and could give the operator an electric shock.

■

Wear ear protectors.

 Exposure to noise can cause 

hearing loss.

■

Make sure that the tool is only connected to the 
voltage marked on the name plate.

■

Never use the tool if its cover or any bolts are 
missing.

 If the cover or bolts have been removed, 

replace them prior to use. Maintain all parts in good 
working order.

■

Always secure tools when working in elevated 
positions.

■

Never touch the blade, drill bit, grinding wheel or 
other moving parts during use.

■

Never start a tool when its rotating component is in 
contact with the work piece.

■

Never lay a tool down before its moving parts have 
come to a complete stop.

■

The use of accessories or attachments other than 
those recommended in this manual might present 
a hazard.

■

When servicing use only identical replacement 
parts.

■

Ambient temperature range for tool during operation is 
between 0°C and 40°C.

■

Ambient temperature range for tool storage is between 
0°C and 40°C.

■

The recommended ambient temperature range for the 
charging system during charging is between 10°C and 
38°C.

ADDITIONAL BATTERY SAFETY WARNINGS

 WARNING

To reduce the risk of 

fi

 re, personal injury, and product 

damage due to a short circuit, never immerse your 
tool, battery pack or charger in 

fl

 uid or allow a 

fl

 uid  to 

fl

 ow inside them. Corrosive or conductive 

fl

 uids,  such 

as seawater, certain industrial chemicals, and bleach 
or bleach-containing products, etc., can cause a short 
circuit.

■

Ambient temperature range for battery during use is 
between 0°C and 40°C.

■

Ambient temperature range for battery storage is 
between 0°C and 20°C.

TRANSPORTING LITHIUM BATTERIES

Transport the battery in accordance with local and national 
provisions and regulations.
Follow all special requirements on packaging and labelling 
when transporting batteries by a third party. Ensure that 
no batteries can come in contact with other batteries 
or conductive materials while in transport by protecting 
exposed connectors with insulating, non-conductive caps 
or tape. Do not transport batteries that are cracked or 
leaking. Check with the forwarding company for further 
advice.

RESIDUAL RISKS

Even when the product is used as prescribed, it is still 
impossible to completely eliminate certain residual risk 
factors. The following hazards may arise and the operator 
should pay special attention to avoid the following:

■

Damage to hearing caused by noise

–

Wear suitable hearing protection and limit exposure.

■

Injury to the eyes

–

Wear protective eye shields or goggles when using 
the product.

■

Injury caused by vibration

–

Limit exposure. Follow the instructions in Risk 
Reduction.

■

Electric shock caused by contact with hidden wires

–

Hold the product only by insulated services.

■

Injury caused by dust

–

Dust created by operating the product can cause 
respiratory injury. Wear appropriate dust control 
mask with filters suitable for protecting against 
particles from the material being worked on.

RISK REDUCTION

It has been reported that vibrations from hand-held tools 
may contribute to a condition called Raynaud’s Syndrome