Makita TW140DZ - Инструкция по эксплуатации - Страница 5

5

ENGLISH

5. 

Do not short the battery cartridge:

(1) 

Do not touch the terminals with any con-
ductive material.

(2) 

Avoid storing battery cartridge in a con-
tainer with other metal objects such as 
nails, coins, etc.

(3) 

Do not expose battery cartridge to water 
or rain.

A battery short can cause a large current 

flow, overheating, possible burns and even a 

breakdown.

6. 

Do not store the tool and battery cartridge in 
locations where the temperature may reach or 
exceed 50 °C (122 °F).

7. 

Do not incinerate the battery cartridge even if 
it is severely damaged or is completely worn 

out. The battery cartridge can explode in a fire.

8. 

Be careful not to drop or strike battery.

9. 

Do not use a damaged battery.

10. 

The contained lithium-ion batteries are subject 
to the Dangerous Goods Legislation require-
ments. 

For commercial transports e.g. by third parties, 

forwarding agents, special requirement on pack-
aging and labeling must be observed. 
For preparation of the item being shipped, consult-
ing an expert for hazardous material is required. 

Please also observe possibly more detailed 

national regulations. 
Tape or mask off open contacts and pack up the 

battery in such a manner that it cannot move 

around in the packaging.

11. 

Follow your local regulations relating to dis-
posal of battery.

12. 

Use the batteries only with the products 

specified by Makita.

 Installing the batteries to 

non-compliant products may result in a fire, exces

-

sive heat, explosion, or leak of electrolyte.

SAVE THESE INSTRUCTIONS.

CAUTION:

Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that 

have been altered, may result in the battery bursting 

causing fires, personal injury and damage. It will 

also void the Makita warranty for the Makita tool and 

charger.

Tips for maintaining maximum 
battery life

1. 

Charge the battery cartridge before completely 
discharged. Always stop tool operation and 
charge the battery cartridge when you notice 
less tool power.

2. 

Never recharge a fully charged battery car-
tridge. Overcharging shortens the battery 
service life.

3. 

Charge the battery cartridge with room tem-
perature at 10 °C - 40 °C (50 °F - 104 °F). Let 
a hot battery cartridge cool down before 
charging it.

FUNCTIONAL 
DESCRIPTION

CAUTION:

Always be sure that the tool is 

switched off and the battery cartridge is removed 
before adjusting or checking function on the tool.

Installing or removing battery 
cartridge

CAUTION:

Always switch off the tool before 

installing or removing of the battery cartridge.

CAUTION:

Hold the tool and the battery car-

tridge firmly when installing or removing battery 

cartridge.

 Failure to hold the tool and the battery 

cartridge firmly may cause them to slip off your hands 

and result in damage to the tool and battery cartridge 

and a personal injury.

1

2

3

►    

1.

 Red indicator 

2.

 Button 

3.

 Battery cartridge

To remove the battery cartridge, slide it from the tool 

while sliding the button on the front of the cartridge.

To install the battery cartridge, align the tongue on the 

battery cartridge with the groove in the housing and slip 

it into place. Insert it all the way until it locks in place 

with a little click. If you can see the red indicator on the 

upper side of the button, it is not locked completely.

CAUTION:

Always install the battery cartridge 

fully until the red indicator cannot be seen.

 If not, 

it may accidentally fall out of the tool, causing injury to 

you or someone around you.

CAUTION:

Do not install the battery cartridge 

forcibly.

 If the cartridge does not slide in easily, it is 

not being inserted correctly.