Einhell TE-BJ 18 Li (4350630) - Инструкция по эксплуатации - Страница 20

GB

- 20 -

6.3 Positioning the biscuit jointer and cutting 

slots (Fig. 14)

Cutting slots with an angle of 0° at a particu-

lar height

• 

Adjust the angle stop (11) to 0° and then in-

sert the height-adjustable stop (14).

• 

Adjust the required height with the aid of the 

height-adjustable stop (14) (see 5.5).

• 

Position the machine close to the workpiece.

• 

There are markings (a) on the machine; the-

se must line up with the line marked on the 

workpiece.

• 

Then switch on the machine and push the 

handle (12) forward. The workpiece must be 

securely clamped when doing this.

Cutting slots with an angle between 0° and 

90°

• 

Adjust the required cutting depth and check 

it (see 5.2).

• 

Adjust the required cutting angle using the 

angle stop (11) (see 5.3).

• 

Position the machine close to the workpiece.

• 

There are markings (a) on the machine; the-

se must line up with the line marked on the 

workpiece.

• 

Then switch on the machine and push the 

handle (12) forward. The workpiece must be 

securely clamped when doing this.

CAUTION! 

The height-adjustable stop (14) must 

only be used with a cutting angle of 0°.

6.4 Connecting the workpieces (Figs. 15-16)

• 

Once you have cut a slot on both workpieces 

they can be connected.

• 

Apply glue in both slots.

• 

Insert the biscuit (a) into one of the slots (Fig. 

15).

• 

Slide both workpieces together (Fig. 16).

• 

Clamp the workpieces and wait until the glue 

has set.

7. Cleaning, maintenance and 

ordering of spare parts

Hazard!

Always pull out the battery pack before starting 

any cleaning work.

7.1 Cleaning

• 

 Keep all safety devices, air vents and the 

motor housing free of dirt and dust as far as 

possible. Wipe the equipment with a clean 

cloth or blow it with compressed air at low 

pressure.

• 

 We recommend that you clean the device  

immediately each time you have finished 

using it.

• 

 Clean the equipment regularly with a moist 

cloth and some soft soap. Do not use 

cleaning agents  or solvents; these could at-

tack the plastic parts of the equipment. Ensu-

re that no water can seep into the device. The 

ingress of water into an electric tool increases 

the risk of an electric shock.

7.2 Maintenance

There are no parts inside the equipment which  

require additional maintenance.

7.3 Ordering replacement parts:

Please quote the following data when ordering 

replacement parts:

• 

 Type of machine

• 

 Article number of the machine

• 

 Identification number of the machine

• 

 Replacement part number of the part required

For our latest prices and information please go to 

www.Einhell-Service.com

8. Disposal and recycling

The equipment is supplied in packaging to pre-

vent it from being damaged in transit. The raw 

materials in this packaging can be reused or 

recycled. The equipment and its accessories are 

made of various types of material, such as metal 

and plastic. Never place defective equipment in 

your household refuse. The equipment should 

be taken to a suitable collection center for proper 

disposal. If you do not know the whereabouts of 

such a collection point, you should ask in your 

local council o

ffi

  ces. 

9. Storage

Store the equipment and accessories in a dark 

and dry place at above freezing temperature. The 

ideal storage temperature is between 5 and 30 

°C. Store the electric tool in its original packaging.

Anl_TE_BJ_18_Li_SPK13.indb   20

10.11.2021   08:20:29