McCulloch CSE2040S - Инструкция по эксплуатации - Страница 19

L. EC DECLARATION OF CONFORMITY

ENGLISH - 9

Husqvarna AB, S-561 82, Huskvarna, Sweden
Declare under our sole responsibility that the product(s);
Designation.................................

Chainsaw

Designation of Type(s).................

CSE1835, CSE1935S, CSE2040, CSE2040S 

Identification of Series.................

See Product Rating Label

Y

ear of Construction....................

See Product Rating Label

Conforms to the essential requirements 

&

 provisions of the following EC Directives:

2006/42/EC, 2004/108/EC, 2000/14/EC, 2011/65/EU

based on the following EU harmonized standards applied:

EN60745-1, EN60745-2-13, EN55014-2, EN55014-1, EN61000-3-2, EN61000-3-11

Notified Body that carried out the EC type-examination
in accordance with article 8 section 2c....................... T

ÜV

 Rheinland LGA Products GmbH

Tillystraße 2
D-90431 Nürnberg
Germany

Certificate no.: ............................................................ BM 50268379
The maximum A weighted sound pressure level L

pA

at the workstation, measured according to EN60745-2-13,

is given in the table.
The maximum hand / arm vibration weighted value a

h 

measured according to EN60745-2-13, on a sample of

the above product(s) is given in the table.
The declared vibration total value has been measured in accordance with a standard test method and may be
used for comparing one tool with another.
The declared vibration total value may also be used in a preliminary assessment of exposure.

Warning:

The vibration emission during actual use of the power tool can differ from the declared total value depending on
the ways in which the tool is used
Operators should identify safety measures to protect themselves that are based on an estimation of exposure in
the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to the trigger time).

2000/14/EC: The Measured Sound Power L

WA

&

 Guaranteed Sound Power L

WA

values are according to the

tabulated figures.
Conformity Assessment Procedure............. Annex V

Ulm  12/02/2013
P. Lamelli
Global R

&D

 Director - Hand held

Keeper of Technical Documentation

EN 61000-3-11 Compliance statement

Depending on the characteristics of the local electricity supply network, use of this product may result in short
voltage drops at the instant of switching on.  This may influence other electrical equipment e.g a momentary
dimming of a lamp.  If the 

Mains impedance Z

max

of your electricity supply is less than the value shown in the

table (applicable to your model) then these effects will not occur.  The value of the network impedance may be
determined by contacting your electricity supply authority

Type (CSE

____)

1835

1935S 2040

2040S

Dry Weight (Kg)

4.3

4.5

4.4

4.6

Power (kW)

1.8

1.9

2.0

2.0

Oil tank volume (cm

3

)

240

240

240

240

Maximum length of guide bar (cm)

35

35

40

40

Chain pitch (mm)

9.52

9.52

9.52

9.52

Chain gauge (mm)

1.3

1.3

1.3

1.3

Measured Sound Power L

WA

(dB(A))

106

106

106

106

Guaranteed Sound Power L

WA

(dB(A))

110

110

110

110

Sound pressure 

L

pA

(dB(A))

95

95

95

95

Uncertainty 

K

pA 

(dB(A))

2.5

2.5

2.5

2.5

Hand / arm vibration

a

h

(m/s

2

)

7.28

7.28

8.08

8.08

Uncertainty 

K

ah

(m/s

2

)

1.5

1.5

1.5

1.5

Mains-Impedance Z

max

(Ohm)

0.382

0.382

0.382

0.382