Metabo SBE 760 - Инструкция по эксплуатации - Страница 11

ENGLISH

en

11

Clamping the tool: 

Insert tool -2- as far as it will go 

and tighten equally in all 3 bores using the chuck 

key -3-.

7.9 Unscrew the chuck (when driving screws 

without the chuck or for use with attach-

ments)

See illustrations A, B, on page 3.

Note for Fig. A, B:

 Release by tapping lightly with a 

rubber hammer, as shown, and unscrew.

Note:

 If a bit clamping bush (order no. 6.31281) is 

attached, the screwdriver bit inserted in the 

hexagon socket of the spindle is held in place.

Cleaning the keyless chuck:

After prolonged use hold the chuck vertically, with 

the opening facing down, and fully open and close it 

several times. The dust collected falls from the 

opening. Regular use of cleaning spray on the jaws 

and jaw openings is recommended.

Use only genuine Metabo accessories.
Use only accessories which fulfil the requirements 

and specifications listed in these operating instruc-

tions. 
Fit accessories securely. Secure the machine if it is 

operated in a bracket. Loss of control can cause 

personal injury.
For a complete range of accessories, see 

www.metabo.com or the main catalogue.

Repairs to electrical tools must be carried out by 

qualified electricians ONLY! 
If you have Metabo electrical tools that require 

repairs, please contact your Metabo service centre. 

For addresses see www.metabo.com.
You can download spare parts lists from 

www.metabo.com.

Observe national regulations on environmentally 

compatible disposal and on the recycling of disused 

machines, packaging and accessories.

Only for EU countries: Never dispose of 

power tools in your household waste! In 

accordance with European Guideline 2002/

96/EC on used electronic and electric equipment 

and its implementation in national legal systems, 

used power tools must be collected separately and 

handed in for environmentally compatible recycling.

Explanatory notes on the information on page 3.

Changes due to technological progress reserved.

P

1

= Rated input

P

2

= Power output

n

1

*

= No-load speed

n

2

*

= Load speed

ø max = Max. drill diameter

s max = Max. impact rate

b

= Chuck capacity

G

= Drill spindle thread

H

= Drill spindle with hexagon socket

m

= Weight

D

= Collar diameter

Measured values determined in conformity with 

EN 60745.

Machine in protection class II

~

Alternating current

The technical specifications quoted are subject to 

tolerances (in compliance with the relevant valid 

standards).

* Energy-rich, high-frequency interference can cause 

fluctuations in speed. The fluctuations disappear, 

however, as soon as the interference fades away.

Emission values

Using these values, you can estimate the emis-

sions from this power tool and compare these with 

the values emitted by other power tools. The actual 

values may be higher or lower, depending on the 

particular application and the condition of the tool or 

power tool. In estimating the values, you should also 

include work breaks and periods of low use. Based 

on the estimated emission values, specify protective 

measures for the user - for example, any organisa-

tional steps that must be put in place. 
Vibration total value (vector sum of three directions) 

determined in accordance with EN 60745:

a

h, ID

= Vibration emission value 

(impact drilling into concrete)

a

h, D

= Vibration emission value

(drilling into metal)

K

h, ID/D

= Uncertainty (vibration)

Typical A-effective perceived sound levels:

L

pA

= Sound pressure level

L

WA

= Acoustic power level

K

pA

, K

WA

= Uncertainty

Wear ear protectors!

8. Cleaning, Maintenance

9. Accessories

10. Repairs

11. Environmental Protection

12. Technical Specifications