Metabo SBE 650 Impuls - Инструкция по эксплуатации - Страница 10

ENGLISH

en

10

See page 2.

1 Chuck key (for geared chuck) *

2 Geared  chuck  *

3 Futuro Plus keyless chuck *

4 Depth  stop  *

5 Additional handle *

6 Direction switch *

7 Sliding switch for normal drilling/impact drilling *

8 Rocker switch for pulse function *

9 Lock button (continuous operation)

10 Trigger

11 Speed preselection wheel *

* depending on the features / model

Before plugging in, check to see that the 

rated mains voltage and mains frequency, 

as stated on the rating label, match with your 

power supply.

Always install an RCD with a maximum trip 

current of 30 mA upstream.
BE 650, SBE 650, SBE 650 Impuls:

Make sure the chuck clamps securely:

After drilling for the first time (clockwise), firmly 

tighten the safety screw inside the chuck using 

a screwdriver. Caution: left-handed thread! 

(see Section 7.9)

6.1 Attaching the Additional Handle

(SB 650, SBE 650, SBE 650 Impuls)

For safety reasons, always use the 

additional handle supplied.

Open the clamping ring by turning the additional 

handle (5) anticlockwise. Push the additional 

handle onto the collar of the machine. Insert the 

depth stop (4). Securely tighten the additional 

handle at the angle required for the application.

7.1 Adjusting the Depth Stop

(SB 650, SBE 650, SBE 650 Impuls)

Loosen the additional handle (5). Set depth stop (4) 

to the desired drilling depth and retighten additional 

handle.

7.2 Switching On and Off

To start the machine, press the trigger switch (10). 
BE 650, SBE 650, SBE 650 Impuls: Press in the 

trigger switch to change the speed. 
For continuous operation the trigger switch can be 

locked using the lock button (9). To stop the 

machine, press the trigger switch again.

In continuous operation, the machine 

continues running if it is forced out of your 

hands. Therefore, always hold the machine 

with both hands using the handles provided, 

stand in a safe position and concentrate.

7.3 Speed Preselection

(BE 650, SBE 650, SBE 650 Impuls)

Select the (11) maximum speed using the 

preselection wheel. See page 4 for recommended 

drilling speeds.

7.4

Switching Between Normal Drilling/

Impact Drilling

(SB 650, SBE 650, SBE 650 Impuls)

Select the desired operating mode by pushing the 

sliding switch (7).

Drilling

Impact drilling

 
Work with high speed settings when impact drilling.

Impact drilling and normal drilling only in 

a clockwise direction.

7.5 Selecting the Direction of Rotation

(BE 650, SBE 650, SBE 650 Impuls)

Do not activate the direction switch (6) 

unless the motor has completely stopped.

Select direction of rotation:

R = Clockwise

L = Anticlockwise

Screw the chuck firmly to the spindle and 

tighten the safety screw inside the chuck 

using a screwdriver. (Caution: left-handed 

thread!) 

Otherwise it may come loose during 

anticlockwise operation (e.g. when 

screwdriving).

7.6 Switching pulse function on and off

(SBE 650 Impuls)

Do not work for long periods with 

pulse function switched on! 

(The motor can overheat.) 

Actuate rocker switch for pulse function (8).

0   = pulse function switched off

 = pulse function switched on

7.7 Tool Change With 

Futuro Plus Keyless Chuck (3)

Quick-action keyless chuck with metal sleeve: 

See illustrations on page 2.
Insert the tool. Hold the retaining ring (a) firmly and 

turn the collet (b) towards "GRIP, ZU" with the other 

hand until the mechanical resistance which can be 

felt is overcome. 

Caution! The tool is not yet clamped!

 Keep 

turning the sleeve (

it must "click" when turning

) 

until it cannot be turned any further - 

only now

 is the 

tool 

securely

 clamped. 

With a soft tool shank, retightening may be required 

after a short drilling period.
Open the chuck:

Hold the retaining ring (a) firmly and turn the collet 

(b) towards "AUF, RELEASE" with the other hand.

5. Overview

6. Commissioning

7. Use