BRAYER BR1003 - Инструкция по эксплуатации - Страница 4

6

7

en

en

•  Transport the kettle in the original package.

•  Keep the unit out of reach of children and disabled

•  persons.

ELECTRIC KETTLE IS INTENDED FOR HOUSEHOLD 

USE ONLY, DO NOT USE THE KETTLE FOR ROOM 

HEATING, FOR INDUSTRIAL OR LABORATORY 

PURPOSES

BEFORE USING THE KETTLE

After unit transportation or storage at low 

temperature, it is necessary to keep it for at least 

three hours at room temperature.

•  Unpack the kettle and remove all the packaging 

materials. 

•  Keep the original package.

•  Check the delivery set.

•  Read the safety measures and operating 

recommendations.

•  Examine the kettle for damages, in case of damage 

do not plug it into the mains.

•  Make sure that the specifications of power supply 

voltage specified on the lower panel of the unit or 

the base correspond to the specifications of your 

mains. When using the kettle in the mains with 60 

Hz frequency, the unit does not need any additional 

settings.

•  Wipe the base (1), the outer and inner surfaces of the 

flask (2) with a clean, slightly damp cloth to remove 

dust. 

ATTENTION!

Be careful while handling the kettle, glass flask (2) 

can break when the kettle is dropped or hit against a 

solid object.

Notes: 

- the operation mode buttons on the control panel 

(9) are sensory, you just need to touch the button 

to switch the necessary operation mode on.

- each touching of buttons is accompanied by a 

sound signal. 

•  Place the base (1) on a solid steady flat and non-slip 

non-metal surface away from heat sources as far as 

possible from the edge of the surface. 

•  Do not place and do not use the kettle in closed 

space, for example, in the cupboard or in closed 

structures — this can lead to its breakage, cause 

harm to the user or damage to his/her property.

•  Wash the flask (2) with neutral detergents, rinse and 

dry. Wipe the outer surface of the flask (2) with a 

slightly damp cloth and then wipe it dry. Do not use 

abrasives and coarse scourers for this.

•  Before connecting the kettle, make sure that there 

are no moisture drops on the base (1), the flask (2), 

the power cord and the power plug.

•  Remove the kettle from the base (1).

•  To fill the kettle with water press the lid opening 

button (6) and open the lid (5).

•  Fill the kettle with water up to the «MAX» mark, 

according to the scale situated on the outer surface 

of the flask (2).

•  Close the lid, make sure that the kettle lid is closed 

tightly.

•  Place the kettle on the base (1).

•  Insert the power plug into the mains socket, you will 

hear a sound signal and the water temperature in the 

kettle flask (2) will appear on the display (10). 

•  Press the On/Off button (12) «   ». The kettle will 

switch on, you will hear a sound signal and the 

illumination (8) of the flask (2) will light up. As water 

is heated, the digital water temperature symbols 

in the flask (2) will be shown on the display (10), 

the On/Off button (12) «   » illumination will be 

flashing, after water starts boiling you will hear sound 

signals, the kettle will switch off automatically, the 

flask illumination (8) will go out, the On/Off button 

(12) «   » illumination will go out.

•  Remove the kettle from the base and carefully pour 

out boiled water into a suitable bowl. 

•  Remember that there is boiling water inside the kettle 

flask (2), always hold the kettle only by the handle 

(7), do not tilt the kettle sharply, in case of careless 

use of the kettle, you can get burns by hot water.

•  Repeat the water boiling procedure several times.

•  Hot water resulting from the first boilings is not 

recommended to consume, you may use it for 

domestic needs.

USING THE ELECTRIC KETTLE

•  Place the base (1) on a solid steady flat and non-slip 

non-metal surface away from heat sources as far as 

possible from the edge of the surface. 

WATER BOILING

•  Remove the kettle from the base (1).

•  To fill the kettle with water press the lid opening 

button (6) and open the lid (5).

•  Fill the kettle with water up to the «MAX» mark, 

according to the scale situated on the outer surface 

of the flask (2).

•  Close the lid, make sure that the kettle lid is closed 

tightly.

•  Place the kettle on the base (1).

•  Insert the power plug into the mains socket, you will 

hear a sound signal and the water temperature in the 

kettle flask (2) will appear on the display (10). 

•  Press the On/Off button (12) «   ». The kettle will 

switch on, you will hear a sound signal and the 

illumination (8) of the flask (2) will light up. As water 

is heated, the digital water temperature symbols in 

the flask (2) will be shown on the display (10), the 

On/Off button (12) «   » illumination will be flashing, 

ATTENTION! 

To avoid burns by hot steam, do not bend over the 

spout (4).