Electrolux ESB5400BK - Инструкция по эксплуатации - Страница 6

6

www.electrolux.com

ENGLISH

Thank you for choosing an Electrolux product. In order to ensure the best results, always use original Electrolux 

accessories and spare parts. They have been designed especially for your product. This product is designed with 

the environment in mind. All plastic parts are marked for recycling purposes.

COMPONENTS

A

. Jug

B

. Spout

C

.  Lid with filler hole

D

.  Measuring cup

E

.  Blade assembly, detachable

F

.  Motor housing

G

.  Speed selector (with PULSE, ICE CRUSH function)*

H

.  Cord storage device (underside of appliance)

I

.  Non-slip feet

*depending on model 

Picture pages 2-3

GETTING STARTED 

(*depending on model )

1 

Before using the blender for the first time

, wash all parts except for the motor housing.

 Assembling:

 Place the 

rubber seal on the blade assembly 

(A) 

and insert it under the jug. Turn the blade assembly counter-clockwise 

(B)

to fasten.  

Caution! The blades are very sharp!

2 

Place the blender on a flat surface

 and lock the jug into position on the motor housing. When the arrow is 

aligned with the “Locked” indicator, the jug is locked in position. Put the ingredients in the jug. 

(Do not exceed 

the maximum level as indicated on the jug.)

3 

Close the lid

(A) 

and insert the measuring cup in the filler hole and 

(B) 

lock into position. (You can use the 

measuring cup to add ingredients while the blender is running. Close the filler hole immediately after, to avoid 

splashing.)  

Caution! When processing hot liquids, see paragraph 4.

4 

Processing hot liquids:

 allow hot liquids to cool down until lukewarm before filling the jug. Fill the jug only 

half full and start processing on low speed. 

The blender jug can become very warm

 – take care to protect your 

hands and to ventilate steam out through the filler hole. 

Always replace the lid before use.Push and hold the 

On-Off button to start mixing.

 The indicator light will illuminate until the On-Off button is released. Release the 

On-Off button to stop mixing. 

Caution!

 If the motor stalls, turn the blender off immediately, unplug the appli-

ance and let it cool for at least 10 minutes.

5 

Start the blender:

 Make sure the speed selector is set to the “OFF”-position. Plug into mains.

Turn the speed 

selector to your desired setting.* The LED light turns on when you operate the speed selector.* 

Note: 

Turn the speed selector to “PULSE, ICE CRUSH” without releasing it, to accelerate the process of blending. 

Release to stop.

6 

Ice crushing:

 Turn the speed selector to “PULSE, ICE CRUSH” for 3-5 seconds several times until you obtain a 

satisfactory result.  

Note:

 You can add more ice through the filler hole while the blender is running.

CLEANING AND CARE

7 

Quick cleaning: 

Pour warm water into the jug, add a few drops of detergent. Mix water and detergent by turning 

the speed selector to “PULSE, ICE CRUSH” briefly. Finally, rinse the jug under running water.

8 

Thorough cleaning:

 Turn the blender off and unplug the power cord. Wipe the motor housing with a damp 

cloth.  

Warning!

 Never immerse the housing, plug, and cord in water or any other fluid

9 

T

Remove the lid and jug. Turn the blade assembly clockwise and remove it. Rinse the blade assembly in water 

and detergent. 

Caution! Handle carefully, the blades are very sharp! 

The lid, jug and measuring cup can be 

washed in the dishwasher.

Enjoy your new Electrolux product!