BRAYER 1201BR - Инструкция по эксплуатации - Страница 4

6

7

en

en

• 

examine the unit for damages; if the unit is damaged, 

do not plug it into the mains.

•  Make sure that the indicated specifications of the 

power supply voltage of the unit correspond to 

the specifications of your mains. When the unit is 

powered from 60 Hz frequency mains, no additional 

actions are necessary.

• 

Remove the lid (2) and remove the measuring cup 

(1).

• 

Wash the bowl (3), the lid (2), the measuring cup (1), 

the lid (8) and the container (9) with warm water and 

neutral detergent, rinse and dry them.

• 

The cutting edges of the knife block (5) are sharp 

and can be dangerous, handle the knife block (5) 

carefully.

• 

Take the chopper bowl (10), turn the knife block (12) 

counterclockwise, remove the knife block (12) and 

the gasket (11).

• 

Wash the chopper bowl (10), the knife block (only 

from the knives side) (12) and the gasket (11) with 

warm water and neutral detergent, rinse and dry.

• 

Clean the motor unit body (6) with a soft, slightly 

damp cloth, and then wipe it dry.

• 

do not immerse the unit, the power cord and the 

power plug of the unit into water or other liquids. 

USING THE BLENDER

• 

The blender is used for chopping products, crushing 

ice, mixing various ingredients and making cocktails.

ATTENTION! Continuous operation time of the 

blender should not exceed 30 seconds, after that 

make at least 1 minute break.

• 

Note: 

— when using the unit for the first time, a 

foreign smell from the electric motor can appear — 

this is normal and it is not covered by warranty.

•  Place the blender on a flat dry and steady surface.

• 

Place the blender bowl (3) on the motor unit (6) and 

turn it clockwise until bumping (pic. 1).

• 

Put the necessary ingredients into the bowl (3).

• 

Cover the bowl (3) with the lid (2).

• 

Insert the measuring cup (1) into the lid (2) opening.

• 

Notes: 

-

the blender is not intended for beating eggs, 

making potato mash, 

-

kneading dough, extracting fruit or vegetable juice, 

crushing hard or frozen products, chopping meat 

and meat products. 

-

the amount of food for processing should not 

exceed 2/3 of the capacity of the bowl (3) and 

should not be below the minimal mark «200» ml 

on the bowl (3).

-

use the scale on the bowl (3) to control the amount 

of products to process.

-

before starting to chop/mix, we recommend to 

peel fruit, remove stones, and cut fruit into 2х2 cm 

cubes.

• 

Make sure once again that the blender bowl (3) is 

installed correctly and is fixed.

• 

Insert the power plug into the socket.

• 

Note:

 — the blender will not be switched on if the 

bowl (3) is installed incorrectly.

• 

Use the operation mode switch (7) to set the required 

rotation speed of the knives:

- «1» (low speed) — for mixing liquid products;

- «2» (high speed) — for liquid and hard products.

- «P» pulse mode. To switch the pulse mode on, 

turn the switch (7) to the position “P” and hold it. 

• 

during the operation or between the operation 

cycles, you can add the required ingredients into the 

bowl (3). To do this, remove the measuring cup (1) 

from the lid (2). After adding ingredients through the 

lid (2) opening, install the measuring cup (1) back to 

its place. 

•  After the unit operation is finished, set the operation 

mode switch (7) to the «0» position and unplug the 

unit. 

• 

Remove the blender bowl (3) from the motor unit (6) 

by turning it counterclockwise (Pic. 1).

• 

Remove the lid (2) from the bowl (3).

• 

Take the processed products out of the bowl (3). 

• 

Wash the blender bowl (3).

• 

Note: 

— if food processing is hindered, add some 

water, liquor or juice etc. into the blender bowl (3).

USING THE CONTAINER (9)
ATTENTION! Do not put hot products or carbonated 

drinks in the container (9).

• 

Remove the knife block (5) from the blender bowl (3), 

to do this, turn it counterclockwise.

• 

Notes: 

• 

the amount of the processed products should not 

exceed 2/3 of the container (9) capacity.

• 

before starting to chop/mix, we recommend to peel 

fruit, remove stones, and cut fruit into 1х1 cm cubes.

• 

if food processing is hindered, you can add some 

water, liquor or juice etc. into the container (9).

• 

Put the necessary ingredients into the container (9).

• 

Install the sealing gasket (4) on the knife block (5), 

install the knife block (5) on the container (9) and turn 

it clockwise (pic. 2).

• 

To avoid damage of the sealing gasket (4) when 

turning the knife block (5), do not apply excessive 

effort.

• 

Install the container (9) on the motor unit (6), slightly 

press on it and turn it clockwise until bumping (pic. 

3).

• 

Use the operation mode switch (7) to set the required 

rotation speed of the knives:

- «1» (low speed) — for mixing liquid products;

- «2» (high speed) — for liquid and hard products.

- «P» pulse mode. To switch the pulse mode on, 

turn the switch (7) to the position “P” and hold it. 

ATTENTION! Continuous operation time should not 

exceed 30 seconds, after that make at least 1 minute 

break.