Turboair Gea 1M/GRFX/A/60 - Инструкция по эксплуатации - Страница 11

11 

To ease the installation, the ring is equipped with an 
index 

G 

that should correspond to the appropriate guide 

H

 placed on the upper air exit.  

11.  

Complete the installation of the discharge tube. 

12. 

Open the extractable drawer 

(Fig.6)

 and apply the 

aesthetic 

Q

 mask (if supplied) with two screws from the 

inside of the hood 

(Fig, 7).

13. 

  Re-install the grease filters, connect the cooker hood to 

the electrical mains and check the perfect operation. 

Description of the hood 

Fig. 8 
1  

Control panel 

2 

  Grease filter (1 or 2 depending on the model in 

possession) 

3 

  Grease filter release handle 

4 

 Lighting 

5 

  Vapour screen (extractable), according to the model 

available, which may be in metal, glass or provided with 
grease filter. 

6 

  Aesthetic mask (Available on the basis of the model in 

possession).  

7 

  Spacer (Available on the basis of the model in 

possession). 

8 

  Wall cabinet (not supplied, the cabinet illustration is 

included to explain the type of installation). 

Operation 

Use the high suction speed in cases of concentrated kitchen 
vapours.  It is recommended that the cooker hood suction is 
switched on for 5 minutes prior to cooking and to leave in 
operation during cooking and for another 15 minutes 
approximately after terminating cooking.  

Maintenance 

ATTENTION! 

Before performing any maintenance operation, 

isolate the hood from the electrical supply by switching off at 
the connector and removing the connector fuse.  
Or if the appliance has been connected through a plug and 
socket, then the plug must be removed from the socket. 

Cleaning 

The cooker hood should be cleaned regularly (at least with the 
same frequency with which you carry out maintenance of the 
fat filters) internally and externally.  Clean using the cloth 
dampened with neutral liquid detergent. Do not use abrasive 
products. 

DO NOT USE ALCOHOL!

WARNING: 

Failure to carry out the basic cleaning 

recommendations of the cooker hood and replacement of the 
filters may cause fire risks.  
Therefore, we recommend oserving these instructions. 
The manufacturer declines all responsibility for any damage to 
the motor or any fire damage linked to inappropriate 
maintenance or failure to observe the above safety 
recommendations. 

Cleaning the glass vapour screen (available only in some 
models)

Fig. 12 

The glass be dismounted and cleaned using a normal glass 
detergent. 
Instructions for removing the glass: 

1.

  Remove the grease filter. 

2.

  Lightly push the glass downwards and allow it slide 

forwards. 

3.

  Remove the glass allowing it to rotate slightly. 

After cleaning, follow the instructions in reverse to remount the 
glass. 

Grease filter 

This must be cleaned once a month using non aggressive 
detergents, either by hand or in the dishwasher, which must 
be set to a low temperature and a short cycle.  When washed 
in a dishwasher, the grease filter may discolour slightly, but 
this does not affect its filtering capacity. 
To remove the grease filter, pull the spring release handle. 

Fig. 9 

Charcoal filter (filter version only) 

It absorbs unpleasant odours caused by cooking. 

2 charcoal filters are required for cooker hoods with 2 motors 
and 1 charcoal for cooker hoods with 1 motor.The saturation 
of the activated charcoal occurs after more or less prolonged 
use, depending on the type of cooking and the regularity of 
cleaning of the grease filter. 
In any case it is necessary to replace the cartridge at least 
every four mounths. 
The carbon filter may NOT be washed or regenerated. 
  

Fig. 10 

Place the carbon filter in order to cover the protection grill 
for the motor fan wheel, then turn the central handle 

P

 of 

the filter clockwise. 
To dismount the central handle 

P 

of the filter turn the 

handle anti-clockwise. 

Replacing lamps 

Fig. 11 

Disconnect the hood from the electricity. 

Warning! 

Prior to touching the light bulbs ensure they are 

cooled down. 

Access the lamp housing area:  

remove the lamp holder using a small screwdriver or 
similar tool as a lever.  
Replace the damaged light bulb.  
Use only 40W max (E14) olive shape light bulbs.  
Then close the lamp housing (snap lock).  

If the lights do not work, make sure that the lamps are fitted 
properly into their housings before you call for technical 
assistance.