Korting KHC 97070 GW - Инструкция по эксплуатации - Страница 13

- 12 -

particles suspended in the air, therefore it is subject to clogging 

with variable frequency according to the use of the appliance.

-  To prevent the danger of possible fires, at least every 2 

months one must wash the anti-grease filters by hand using 

non-abrasive neutral liquid detergents or in the dishwasher 

at low temperatures and on short cycles.

-  After a few washes, colour alterations may occur. This does 

not give the right to claim their replacement.

•  The  active  carbon  filters

 are used to purify the air that is 

sent back into the room and its function is to mitigate the 

unpleasant odours produced by cooking.

-  The non-regenerable active carbon filters must be replaced 

at least every 4 months. The saturation of the active charcoal 

depends on the more or less prolonged use of the appliance, 

on the type of kitchen and on the frequency with which anti-

grease filter is cleaned.

-  Regenerable active charcoal filters must be washed by hand, 

with non abrasive neutral detergents, or in the dishwasher at 

a maximum temperature of 65°C (the washing cycle must be 

complete without dishware). Remove excess water without 

damaging the filter, remove the plastic parts, and let the 

mat dry in the oven for at least 15 minutes approximately at 

a maximum temperature of 100°C. To keep the regenerable 

charcoal filter functioning efficient this operation must be 

repeated every 2 months. These must be replaced at least 

every 3 years or when the mat is damaged.

•  Before remounting the anti-grease filters and the regen

-

erable active charcoal filters it is important that they are 

completely dry.

•  Clean the hood frequently, both internally and externally, 

using a cloth dampened with denatured alcohol or neutral 

liquid detergents that are non abrasive.

•  

The lighting .system is designed for use during cooking 

and not for the prolonged general lighting of the room. The 

prolonged use of the lighting system significantly decreases 

the average duration of the bulbs.

•  

If the appliance is equipped with courtesy lights it is possible 

to use them for general room lighting for a prolonged amount 

of time.

•  Attention:

 the non compliance with the hood cleaning 

warnings and with the replacement and cleaning of the filters 

entails risk of fires. One therefore recommends keeping to the 

suggested instructions.

•  Replacing halogen light bulbs (Fig.11A):

To replace the halogen light bulbs 

B

, remove the glass pane

C

 using a lever action on the relevant cracks. Replace the bulbs 

with new ones of the same type. 

Caution:

 do not touch the 

light bulb with bare hands.

•  Replacing LED lamps (Fig.11B):

If the appliance version is with LED lamps, the intervention of 

a specialised technician is necessary to replace them.

•  Commands (Fig.12):

NOTE:

 with this command it is also possible to control the ap-

pliance using a remote control, to be requested as an accessory.

A Button

 = Switches the hood on/off. The equipment switches 

on at the 1st speed. 

B Button

 = Decreases motor speed.

C Display

 = Shows the selected motor speed and timer acti-

vation/intense speed/filter warning.

D Button

 = Increases motor speed.

Pressing the 4th speed button engages the intense function 

for 6 minutes, then the equipment goes back to working at 

the speed at which it was activated. During this function, the 

number 4 flashes on the display.

- If you wish to deactivate the function before the 6 minutes, 

press the 

B 

button.

Attention! 

Some models only work up to the 3rd speed and, 

therefore, do not have the intense function.

E Button

 = Pressing this button activates the Timer function 

even with any of the 1-2-3 speeds engaged (except the Intense 

function speed). When the Timer function is active, the set 

speed must flash on the display when the timer is activated.

After 15 minutes, at the end of the countdown, the hood 

switches off (motor and any lights remain on).

If the intense speed is engaged, the Timer cannot be activated.

- If you wish to deactivate the function before the 15 minutes, 

press the 

E

 button.

F Button 

= Switches the lights on/off.

•  Anti-grease/active charcoal filters saturation:

- After 

30 h

 of operation, when the 

C

 display flashes, alternating 

the working speed with the letter 

F

 (i.e. 

2

 and 

F

), this means 

that you need to wash the anti 

grease filters

.

- After 

120 h

 of operation, when the 

C

 display flashes, alterna-

ting the working speed with the letters 

C/F

 (i.e.

 2

 and 

C/F

), this 

means that you need to wash or replace the 

charcoal filters

.

- Once you have repositioned the clean filter, you need to reset 

the electronic memory with the hood on, pressing the 

B

 button 

for about 

3 seconds

. 

After that time, the letter 

E

 appears on the display (reset 

confirmed) and the hood switches off.

• Mechanical controls (Fig.13): 

the symbols are as follows:

A

= LIGHT / ON-OFF key

B

= OFF /FIRST SPEED key 

C

= SECOND SPEED key

D

 = THIRD SPEED key

If the hood is shut off at first, second or third speed, when 

it is turned back on, it will start at the same speed it was in 

when switched off.

THE MANUFACTURER DECLINES ALL RESPONSIBILITY 

FOR EVENTUAL DAMAGES CAUSED BY BREACHING THE 

ABOVE WARNINGS.