Jetair Viki BL 60 A - Инструкция по эксплуатации - Страница 18

18 

•  If possible, disconnect and move freestanding or slide-in 

range from cabinet opening to provide easier access to rear 
wall/ceiling. Otherwise put a thick, protective covering over 
countertop, cooktop or range to protect from damage and 
debris. Select a flat surface for assembling the unit. Cover 
that surface with a protective covering and place all canopy 
hood parts and hardware in it. 

•  In addition check whether near the installation area of the 

hood (in the area accessible also with the hood mounted) an 
electric socket is available and it is possible to connect a 
fumes discharge device to the outside (only suction version).  

• 

Carry out all the masonry work necessary (e.g. installation of 
an electric socket and/or a hole for the passage of the 
discharge tube). 

  
Expansion wall plugs are provided to secure the hood to most 
types of walls/ceilings. However, a qualified technician must verify 
suitability of the materials in accordance with the type of 
wall/ceiling. The wall/ceiling must be strong enough to take the 
weight of the hood. 

Do not tile, grout or silicone this appliance 

to the wall. Surface mounting only. 

  
In the case of the presence of panels and/or walls and/or lateral 
wall units check that there is sufficient space to install the hood and 
that access to the command panel is easy. 
  

Operation 

Use the high suction speed in cases of concentrated kitchen 
vapours.  It is recommended that the cooker hood suction is 
switched on for 5 minutes prior to cooking and to leave in 
operation during cooking and for another 15 minutes 
approximately after terminating cooking.  
  

Model with touch panel 

To select the functions of the hood just touch the commands. 
 

Light key ON/OFF 

Intensive speed selection key

(suction 

power) - duration 5 minutes - press again to 
return to previous setting. 

High-speed selection key 

(suction power). 

Medium-speed selection key

(suction power) 

- when flashing it indicates the need to wash or 
replace the carbon filter. This signal is normally 
deactivated. To activate the alarm, disable the 
electronic by pressing the 

0

button for 3 

seconds.  
Next, simultaneously press buttons 

1

 and 

2

for 

3 seconds; at first, only button 

1

will flash, then 

both buttons 

1

 and 

2

will flash to indicate 

activation. Repeat the procedure to deactivate 
the alarm; at first buttons 

1

 and 

2

will flash and 

subsequently only button 

1

to indicate 

deactivation. 

Low-speed selection key

 (suction power) – 

when flashing it indicates the need to wash the 
fats filter. 

Motor key OFF

 (stand by) – excludes the 

electronics – reset wash/replace filters signals. 

MOTOR OFF 

Press briefly to switch the motor off. 

RESET FILTERS SIGNALS

In functioning mode, after carrying out filter 
maintenance, press the key until hearing the 
sound signal. The flashing LED 

1 

(grease filter) 

or 

2 

(carbon filter) stops flashing. 

EXCLUDING THE ELECTRONICS

Press the key for 3 seconds. The hood 
command electronics will be excluded. 
This function can be useful during the product 
cleaning operations. 
Just repeat the operation to reinsert the 
electronics.  

 
If the hood fails to operate correctly, briefly disconnect it from 
the mains power supply for almost 5 sec. by pulling out the 
plug. Then plug it in again and try once more before 
contacting the Technical Assistance Service. 

Model with 5 push-buttons control panel 

T1.  Button ON/OFF lights 

(Led 

L1

 lit) 

T2.  Button OFF – Selection button suction speed (power) 1 

(Led 

L2

 lit) 

T3.  Selection button suction speed (power) 2 

(Led 

L2+L3

 lit) 

T4.  Selection button suction speed (power) 3 

(Led 

L2+L3+L4

liti)

T5.  Selection button intensive suction speed (power) 

(Led 

L2+L3+L4

 lit + Led 

L5

 flashing) - duration 5 minutes – after 

which the hood automatically sets suction speed (power) 

2

. 

Delayed switch-off of the hood (flashing LEDs):

It is possible to set the delayed hood switch-off by pressing again 
for more than 2 seconds the button of the suction speed (power) 
active at that time.  
The available delayed switch-off options are: 
Suction speed (power) 

1

: 

20 minutes 

Suction speed (power) 

2

: 

15 minutes 

Suction speed (power) 

3

: 

10 minutes 

Intensive

 suction speed (power): 

5 minutes