Gorenje TH60E3B - Инструкция по эксплуатации - Страница 8

Appliance designed, tested and manufactured according to:

•

Safety: EN/IEC 60335 -1; EN/IEC 60335 -2-31, EN/IEC 62233. 

•

Performance:  EN/IEC  61591;  ISO  5167-1;  ISO  5167-3;  ISO  5168;  EN/IEC  60704-1;  EN/IEC  60704-2-13;  ISO  3741; 
EN 50564; IEC 62301. 

•

EMC: EN 55014-1; CISPR 14-1; EN 55014-2; CISPR 14-2; EN/IEC 61000 -3-2; EN/IEC 61000 -3-3. 

USE

The hood is designed to be used either for exhausting or filter version.

This  appliance  is  marked  according  to  the  European  directive  2012/19/EC  on  Waste  Electrical  and  Electronic  Equipment 
(WEEE).  By  ensuring  this  product  is  disposed  of  correctly,  you  will  help  prevent  potential  negative  consequences  for  the 
environment and human health, which could otherwise be caused by inappropriate waste handling of this product.

The symbol                 

on the product, or on the documents accompanying the product, indicates that this appliance may not 

be treated as household waste. Instead it should be taken to the appropriate collection point for the recycling of electrical and 
electronic  equipment.  Disposal  must  be  carried  out  in  accordance  with  local  environmental  regulations  for  waste  disposal.
For further detailed information regarding the process, collection and recycling of this product, please contact the appropriate 
department  of  your  local  authorities  or  the  local  department  for  household  waste  or  the  shop  where  you  purchased  this 
product.

Suggestions for a correct use in order to reduce the environmental impact: Switch ON the hood at minimum speed when you 
start cooking and kept it running for few minutes after cooking is finished. Increase the speed only in case of large amount of 
smoke  and  vapour  and  use  boost  speed(s)  only  in  extreme  situations.  Replace  the  charcoal  filter(s)  when  necessary  to 
maintain  a  good  odour  reduction  efficiency.  Clean  the  grease  filter(s)  when  necessary  to  maintain  a  good  grease  filter 
efficiency.  Use  the  maximum  diameter  of  the  ducting  system  indicated  in  this  manual  to  optimize  efficiency  and  minimize 
noise. 

Additional Installation Specifications:
 Use only the fixing screws supplied with the product for installation or, if not supplied, purchase the correct screws type. Use 
the correct length for the screws which are identified in the Installation Guide.
 In case of doubt, consult an authorised service assistance centre or similar qualified person. 

WARNING! 

Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards. 

In  this  case  the  fumes  are  conveyed  outside  of  the  building  by  means  of  a  special  pipe  connected  with  the  connection  ring 
located on top of the hood.

Attention!

 The exhausting pipe is not supplied and must be purchased apart. Diameter of the exhausting pipe must be equal 

to that of the connection ring.
In  the  horizontal  runs  the  exhausting  pipe  must  be  slightly  slanted  (about  10°)  and  directed  upwards  to  vent  the  air  easily 
from the room to the outside.

Attention!

 If the hood is supplied with active charcoal filter, then it must be removed.

Connect the hood and discharge holes on the walls with a diameter equivalent to the air outlet (connection flange).
Using  the  tubes  and  discharge  holes  on  walls  with  smaller  dimensions  will  cause  a  diminution  of  the  suction  performance 
and a drastic increase in noise.
Any responsibility in the matter is therefore declined.

8

DUCTING VERSION