Falmec SOFFIO IS.58 - Инструкция по эксплуатации - Страница 26

26

USING THE RADIO CONTROL

WARNINGS!:

Place the hood away from sources of electromagnetic waves (e.g. micro-
wave ovens), which could interfere with the radio control and with the hood 

electronics.
The maximum operating distance is 5 metres, that may vary according to the pres-
ence of electromagnetic interferences. 
Radio control operated at 433.92MHz.
The radio control consists of two parts:
- the receiver built into the hood;
- the transmitter shown here in the igure.

DESCRIPTION OF TRANSMITTING COMMANDS

UP

Motor switch-on and speed increase from 1 
to 4. Speed 4 is only active for a few minutes.

DOWN

Speed decrease and motor switch-of.

Light ON-OFF

TIMER ON: 

The motor automatically switch-

es of after 15 min.
The function is automatically disabled if the 

motor is switched of (

 key)

Command transmission active

ACTIVATION PROCEDURE (

only for Vetra Wall)

Before using the radio control, follow the procedure below on the 

hood pushbutton panel

:

•

  Press LIGHT (

) and TIMER (

) simultaneously until all LEDs start lashing. 

•

  Release the two keys and press LIGHT (

) again until all LEDs are lit up. 

•

  Release LIGHT (

): now the receiver is active.

This procedure is also used to deactivate the receiver.

RADIO CONTROL CODE CHANGE

With only one radio control, go directly to point 2.
With several radio controls in the same room, a new code can be created by following the 
procedure below.

Disconnect the power to the hood before starting the procedure.

1) - CREATE A NEW CODE

The procedure is to be carried out on the radio control.

•

  Press LIGHT 

 and TIMER 

 simultaneously until the display starts lashing.

•

  Press DOWN 

 on the radio control: saving is conirmed by three brief lashes of the 

display. The new code cancels and replaces the previous default code. 

Reconnect the hood to the electrical power supply, making sure that the 
lights and motor are of. 

2B) - ASSOCIATING THE RADIO CONTROL WITH THE HOOD
           USING THE ROTARY CONTROL
 

press LIGHT (

)

on the hood pushbutton panel

 for 2 seconds:

the red LED lights up. 
press any key on the radio control within 10 seconds. 

2A) - ASSOCIATING THE RADIO CONTROL WITH THE HOOD
           USING THE ELECTRONIC PUSHBUTTON PANEL
 

press TIMER (

)

on the hood pushbutton panel

 for 2 seconds:

the red LED lights up. 
press any key on the radio control within 10 seconds. 

RESTORING DEFAULT CODE

the procedure is to be carried out if the hood is disposed of, sold or transferred.

Disconnect the power to the hood before starting the procedure.

•

  Press UP 

 and DOWN 

 simultaneously on the radio control for more than 5 sec-

onds: reset is conirmed by three brief lashes of the display. 

•

  Reconnect the hood to the electrical power supply.

•

  Proceed with associating the hood and the radio control, as described in point 2.

MAINTENANCE

Before cleaning or carrying out maintenance operations, disconnect the 
equipment by removing the plug or switching of the main switch.
Do not use detergents containing abrasive, acidic or corrosive substances 
or abrasive cloths.

Regular maintenance guarantees proper operation and performance over time.
Special attention is to be paid to the 

metal anti-grease ilters 

: frequent cleaning of the 

ilters and their supports ensures that no lammable grease is accumulated.

CLEANING OF EXTERNAL SURFACES

You are advised to clean the external surfaces of the hood 

at least once every 15 days

to 

prevent oily substances and grease from sticking to them. 
Alternatively 

and for all the other types of surfaces

, it can be cleaned using a damp cloth, 

slightly moistened with mild, liquid detergent or denatured alcohol.
Finish of cleaning by rinsing well and drying with soft cloths. 

Do not use too much water next to the push button control panel and 
lighting devices in order to prevent humidity from reaching electronic 
parts.

The glass panels can only be cleaned with speciic, non-corrosive or non-abrasive deter-
gents using a soft cloth.
The Manufacturer declines all responsibility for failure to comply with these instructions.

CLEANING OF INTERNAL SURFACES

It is forbidden to clean electrical parts, or parts related to the motor inside 
the hood, with liquids or solvents.

For the internal metal parts, see the previous paragraph.