Elica YE WH/A/66 - Инструкция по эксплуатации - Страница 27

27 

Operation 

Use the high suction speed in cases of concentrated kitchen 
vapours.  It is recommended that the cooker hood suction is 
switched on for 5 minutes prior to cooking and to leave in 
operation during cooking and for another 15 minutes 
approximately after terminating cooking.  

Note:

 if the hood does not work, make sure that it is ON by 

using the ON/OFF button. 
The button is inside the hood and can be reached by 
removing the grease filter. 

Fig. 19 

Using the remote control 

The remote control is able to control all the functions of the 
hood:  

Select the suction speed (power)  

 Light 

ON/OFF 

 Not 

implemented 

 Not 

implemented 

Selecting the suction speed (power): 

Press the "

◄

" key or the "

►

" key until you see the symbol 

relating to the “Select the suction speed (power)” function.   
Press the “+” key or the “-” key or the "

■

" key respectively to 

increase or diminish or switch off (stand-by) the speed 
(suction power).  
 

Light ON/OFF: 

Press the "

◄

" or "

►

" button, until the LED corresponding to 

the "Light ON/OFF" symbol appears on the remote control. 
Press the “+” or “-” button to put on or off the lights.  
Press the "

■

" to change the status of the lights, from off (all 

lights) to on (all lights) and vice-versa. 

Configuration of the remote control 

To enable the remote control, proceed as follows: 
Press the "

◄

" or "

►

" button until you can see on the remote 

control the symbol "

" related to the function “Reset and 

configuration of the filter saturation signalling” and press 
continuously on the central button "

■

" for at least 5 seconds. 

An audible signal indicates the successful configuration. 

Maintenance of the remote control

Cleaning the remote control:  

Clean the remote control with a damp cloth and a neutral 
solution of detergent without abrasive substances. 
 

Changing the battery:   

• 

Open the battery casing using a small screwdriver with a 
flat point.  

• 

Change the finished battery with a new one of 12 V type 
MN21/23 

In inserting the new battery respect the polarity indicated 
on the battery casing!  

• 

Close the battery casing up again.  

Disposal of the batteries 

Ultimate disposal of the batteries should be handled according 
to all national laws and regulations. Do not place used 
batteries in your regular waste. 
Ultimate disposal of the batteries must be done safely

.

Contact your local waste management officials for other 
information regarding the environmentally sound collection, 
recycling, and disposal of the batteries. 

Maintenance 

ATTENTION! 

Before performing any maintenance operation, 

isolate the hood from the electrical supply by switching off at 
the connector and removing the connector fuse.  
Or if the appliance has been connected through a plug and 
socket, then the plug must be removed from the socket. 

Cleaning 

The cooker hood should be cleaned regularly (at least with the 
same frequency with which you carry out maintenance of the 
fat filters) internally and externally.  Clean using the cloth 
dampened with neutral liquid detergent. Do not use abrasive 
products. 

DO NOT USE ALCOHOL!

WARNING: 

Failure to carry out the basic cleaning 

recommendations of the cooker hood and replacement of the 
filters may cause fire risks.  
Therefore, we recommend observing these instructions. 
The manufacturer declines all responsibility for any damage to 
the motor or any fire damage linked to inappropriate 
maintenance or failure to observe the above safety 
recommendations. 
The hood should be cleaned regularly (at least with the same 
frequency with which you perform the maintenance of the 
grease filters) internally and externally. 
The chimney and the body of the hood are produced in 

CRISTALPLANT

®

. 

Note: For more details on the material 

CRISTALPLANT

®

 and 

the Manufacturer, visit 

www.cristalplant.it

Maintenance of CRISTALPLANT

®

 DAILY 

CARE 

CRISTALPLANT

®

 requires an easy and quick daily care. 

It is enough to clea 

CRISTALPLANT

®

 using soap and 

water or common detergents to remove most of the dirt 
and stains that may be deposited on the surface. It is 
particularly recommended to rinse the surface well and to 
use gel or abrasive detergents with abrasive sponges like 
“Scotch Brite©” as in attached sample; doing that way, 
the original matt finish, distinguishing feature of 

CRISTALPLANT

®

, will keep untouched. 

HOW TO PREVENT FROM DAMAGES 

The surface is generally strongly resistant against stains 
and spots; nonetheless aggressive chemical products, 
such as acetone, trichloroethylene, strong acids or bases 
are not recommended. After long contact periods, several 
substances like ink, cosmetics and dyes, may leave