Вытяжки Elica ADAGIO BL/F/120 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
17
Use of the remote control
the remote control can control all the functions of the hood:
Selection of the suction speeds (powers)
Control of the light
Key without functions
Reset and configuration of the filter saturation signal
Selection of the suction speeds (powers):
Press key "
◄
" or "
►
" until the following symbol is displayed
on the remote control: ”
Press key “+” or “-” or "
■
" respectively to increase or reduce or
switch off the suction speed (power).
When the hood is off and the suction panel closed,
by
pressing key "
■
" or “+”, the hood activates the opening of the
suction panel first and then sets the hood to the suction speed
(power) 1.
When the hood is on and the suction panel open
press key
"
■
" once to switch off the hood, press again to close the
suction panel (if it is on, the light is switched off as well).
Light control:
Press key "
◄
" or "
►
" until the remote control displays the
symbol
The central light can be switched on and off in two ways:
1.
Press key “+” or “-” respectively to switch on (ON) or off
(OFF) the central light.
2.
Press
key
"
■
" to change the light state from off (OFF) to
on (ON) or viceversa.
Note 1:
if the suction panel is closed, the key switching on the
light opens the panel first.
Note 2:
With the light switched on, press key "
■
" once to
switch off the hood, if no suction speed (power) is selected,
the suction panel is closed by pressing again.
Reset and configuration of the filter saturation signal
Switch on the hood at any speed (see paragraph above
“Selection of the suction speeds (powers)”)
Press key "
◄
" or "
►
" until the remote control displays the
symbol
Press keys “+” and “-“ contemporaneously for more than 3
seconds, all the suction speed LEDs (powers) stop flashing,
showing that the reset of the signal has been carried out.
Maintenance of the remote control
Cleaning the remote control:
Clean the remote control with a damp cloth and a neutral
solution of detergent without abrasive substances.
Changing the battery:
•
Open the battery casing using a small screwdriver with a
flat point.
•
Change the finished battery with a new one of 12 V type
MN21/23
In inserting the new battery respect the polarity indicated
on the battery casing!
•
Close the battery casing up again.
Disposal of the batteries
Ultimate disposal of the batteries should be handled according
to all national laws and regulations. Do not place used
batteries in your regular waste.
Ultimate disposal of the batteries must be done safely
.
Contact your local waste management officials for other
information regarding the environmentally sound collection,
recycling, and disposal of the batteries.
Operation anomalies
The hood does not work
Make sure that:
•
There is no current blackout
•
A speed has been effectively selected.
•
The panel is correctly hooked.
•
The 9-pole connection is well inserted (
Picture 9b
).
• The red reset key above the electric system box is
pressed.
•
The wires in the 9-pole connection are well inserted into
the connector. (During connection, exerting an
overpressure may cause the contacts to bend).
The hood has low efficiency
Make sure that:
•
The motor speed selected is sufficient for the quantity of
fumes present
•
The kitchen is aired enough to allow an air intake and the
charcoal filter is not worn out (filter version hood).
•
The air outlet pipe is not clogged.
•
The suction unit non-return valves can rotate freely.
The hood stops during operation
Make sure that:
•
There is no current blackout
•
The differential magnetothermal switch (automatic circuit
breaker) has not been released.
