De Dietrich DHD 792 X - Инструкция по эксплуатации - Страница 7

35 

If the instructions for installation for the gas hob specify a 
greater distance, this must be adhered to. 

  Electrical connection 

The mains power supply must correspond to the rating 
indicated on the plate situated inside the hood. If provided with 
a plug connect the hood to a socket in compliance with current 
regulations and positioned in an accessible area. If it not fitted 
with a plug (direct mains connection) or if the plug is not 
located in an accessible area apply a bi-polar switch in 
accordance with standards which assures the complete 
disconnection of the mains under conditions relating to over-
current category III, in accordance with installation 
instructions. 

Warning: 

Before re-connecting the hood circuit to the mains 

supply and checking the efficient function, always check that 
the mains cable is correctly assembled. 

Mounting 

Fig. 5-6 
Before beginning installation: 

• 

Check that the product purchased is of a suitable size for 
the chosen installation area. 

•  To facilitate installation, remove the fat filters and the 

other parts allowed and described here, dismantle and 
mount it. 

To remove see also the relative paragraphs. 

• 

Remove the active carbon (*) filter/s if supplied (see also 
relative paragraph). This/these is/are to be mounted only 
if you want lo use the hood in the filtering version. 

•  Check (for transport reasons) that there is no other 

supplied material inside the hood (e.g. packets with 
screws (*), guarantees (*), etc.), eventually removing 
them and keeping them. 

• 

If possible, disconnect and move freestanding or slide-in 
range from cabinet opening to provide easier access to 
rear wall/ceiling. Otherwise put a thick, protective 
covering over countertop, cooktop or range to protect 
from damage and debris. Select a flat surface for 
assembling the unit. Cover that surface with a protective 
covering and place all canopy hood parts and hardware 
in it. 

•  Disconnect the hood during electrical connection, by 

turning the home mains switch off. 

• 

In addition check whether near the installation area of the 
hood (in the area accessible also with the hood mounted) 
an electric socket is available and it is possible to 
connect a fumes discharge device to the outside (only 
suction version).  

•  Carry out all the masonry work necessary (e.g. 

installation of an electric socket and/or a hole for the 
passage of the discharge tube). 

Expansion wall plugs are provided to secure the hood to most 
types of walls/ceilings. However, a qualified technician must 
verify suitability of the materials in accordance with the type of 
wall/ceiling. The wall/ceiling must be strong enough to take 
the weight of the hood. 

Do not tile, grout or silicone this 

appliance to the wall. Surface mounting only. 

An aesthetic flue can be purchased as an optional accessory. 
Check with the assistance centre whether the model in your 
possession envisages this possibility.  
We advise installing the hood after having purchased the flue 
to check with certainty the most suitable installation.   
• 

Trace a central line on the wall in order to ease mounting 
(

1

), position the hole template in a way that the middle 

line printed on top corresponds to the central line marked 
previously and the lower side of the mask corresponds to 
the lower part of the hood once mounted. 

(2). 

•  Make 3 holes Ø 8 mm with a drill and fix the support 

bracket with two dowels and screws to the wall 

(3), 

insert 

the third dowel into the lower hole. 

• 

Only for chimney installation:

 Apply the support 

bracket 

„G“

 to the adherent ceiling, use the chimney 

support bracket as a hole scheme (if present, the small  
eyelet found on the support should coincide with the line 
previously traced on the wall) and trace with a pencil 2 
holes, drill the holes (Ø8mm), insert 2 plugs.  

Fasten the support bracket to the wall with 2 5x45mm 
screws 

(4)

. 

•   Open the vapour scheme and remove the grease filters 

(see relevant paragraph). 

•   Hang the hood 

(5)

, regulate the position 

(6-7) 

and fasten 

it securely with one screw and washer

(8)

. 

•  Carry out electrical connections 

(9)

, but leave the hood 

disconnected from the general electrical main panel. 

•   Install the flange supplied on the exit hole of the hood 

(10a)

. 

• 

Carry out the connection of one tube (

11 

– tube and ties 

for fastening not included, they need to be bought) for the 
fume discharge to the connection ring placed on top of 
the extractor motor unit.  

The other end of the tube should be connected to a fume 
expulsion device towards the outside, in case the hood is 
used in extractor version. 

• 

Fix the upper cover with 3 screws.

(12)

Note:

 this is supplied already mounted in some cases. 

• 

Only for chimney installation: 

In case you want to use 

the hood in filtering version, fasten the deflector 

F 

to the 

support bracket, and connect the other side of the tube to 
the connection ring placed on the deflector 

(13)

. 

Apply the chimneys and fasten them on with two screws 
(

14a

) to the chimney support bracket 

„G“

  (

14b

). and 

make the lower part of the chimney slide into the suited 
part on top of the chimney. 

•   Mount the grease filters and close the vapour scheme.  
 

Warning! 

If the hood has to be used in extractor version, 

remove, if supplied, the carbon filter and the fastening 
wand (placed on the back of the grease filters – see 
relative paragraph).  

If the hood has to be used in filtering version, make sure 
that the carbon filter is already mounted on the back of 
the grease filter, or in case it’s missing, buy it and install 
it. 

Note – only for installation without chimneys: 

In case 

you want to use the hood in filtering version, install the 
grille/deflector instead of the flange 

(10b)

.