Makita DUB184Z - Инструкция по эксплуатации - Страница 7

7 ENGLISH

5. 

Do not short the battery cartridge:

(1) 

Do not touch the terminals with any con-

ductive material.

(2) 

Avoid storing battery cartridge in a con-

tainer with other metal objects such as 

nails, coins, etc.

(3) 

Do not expose battery cartridge to water 

or rain.

A battery short can cause a large current 

flow, overheating, possible burns and even a 

breakdown.

6. 

Do not store the tool and battery cartridge in 

locations where the temperature may reach or 

exceed 50 °C (122 °F).

7. 

Do not incinerate the battery cartridge even if 

it is severely damaged or is completely worn 

out. The battery cartridge can explode in a fire.

8. 

Be careful not to drop or strike battery.

9. 

Do not use a damaged battery.

10. 

The contained lithium-ion batteries are subject to 

the Dangerous Goods Legislation requirements. 

For commercial transports e.g. by third parties, 

forwarding agents, special requirement on pack

-

aging and labeling must be observed.

For preparation of the item being shipped, consult

-

ing an expert for hazardous material is required. 

Please also observe possibly more detailed 

national regulations. 

Tape or mask off open contacts and pack up the 

battery in such a manner that it cannot move 

around in the packaging.

11. 

When disposing the battery cartridge, remove 

it from the tool and dispose of it in a safe 

place. Follow your local regulations relating to 

disposal of battery.

12. 

Use the batteries only with the products 

specified by Makita.

 Installing the batteries to 

non-compliant products may result in a fire, exces

-

sive heat, explosion, or leak of electrolyte.

13. 

If the tool is not used for a long period of time, 

the battery must be removed from the tool.

SAVE THESE INSTRUCTIONS.

CAUTION:

Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that 

have been altered, may result in the battery bursting 

causing fires, personal injury and damage. It will 

also void the Makita warranty for the Makita tool and 

charger.

Tips for maintaining maximum 

battery life

1. 

Charge the battery cartridge before completely 

discharged. Always stop tool operation and 

charge the battery cartridge when you notice 

less tool power.

2. 

Never recharge a fully charged battery cartridge. 

Overcharging shortens the battery service life.

3. 

Charge the battery cartridge with room tempera-

ture at 10 °C - 40 °C (50 °F - 104 °F). Let a hot 

battery cartridge cool down before charging it.

4. 

Charge the battery cartridge if you do not use 

it for a long period (more than six months). 

ASSEMBLY

CAUTION:

Always be sure that the machine is 

switched off and the battery cartridge is removed 

before carrying out any work on the machine.

Installing the front nozzle

1.

Loosen 2 screws with the hex wrench, and then 

pull the screws all the way.

► 

Fig.1:

1.

 Screw

2.

Make sure that the Makita logo on the front nozzle 

is facing the direction shown in the figure, and then 

attach the front nozzle to the machine.

► 

Fig.2:

1.

 Front nozzle

3.

Tighten the screws with the hex wrench.

► 

Fig.3:

1.

 Screw

Installing the flat nozzle or 

extension nozzle

Optional accessory

1.

Attach the adapter pipe to the front nozzle, and 

then turn it clockwise to lock it into place.

► 

Fig.4:

1.

 Adapter pipe 

2.

 Front nozzle

2.

  Attach the flat nozzle or extension nozzle to the 

adapter pipe, and then turn it to lock it into place.

► 

Fig.5:

1.

 Flat nozzle 

2.

 Extension nozzle 

3.

 Adapter 

pipe

Attaching the shoulder strap

Optional accessory

CAUTION:

Be sure to attach the hooks of 

the shoulder strap to the machine securely.

 If the 

hooks are attached incompletely, they may come off 

and cause an injury.

CAUTION:

Be sure to use the shoulder strap 

dedicated to this machine.

 Using other shoulder 

strap may cause an injury.

Attach the hooks of the shoulder strap to the machine 

as shown in the figure.

► 

Fig.6:

1.

 Hook

You can also attach the shoulder strap to the machine 

as shown in the figure by attaching one end of the 

shoulder strap to the buckle of the shoulder strap.

► 

Fig.7:

1.

 Buckle