Варочная панель Fulgor Milano CH 302 ID TC WH/2 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
20
21
GB
Display
Description
Probable Cause
Solution
C
The symbol C means that this
cooking point can be configured
No error, the User is in the
configuration menu
Place the pan on the induction
module
C/-
A flashing “C” means that this
cooking point is currently configured.
“-” appears on the display after
configuration.
If the symbol “-” does not appear,
you must check for the possible
causes of E/5.
No error, the User is in the
configuration menu
Wait for “-” or stop the configuration
with the corresponding selection
key; the C symbol stops flashing.
E
A flashing “E” on all the cooking
point displays means that, at this
time, all configurations have been
erased.
No error, the User is in the
configuration menu
Manual re-configuration
E/2
(the error code may be
different for some TCs)
The induction modules are too hot
1. pan/glass temperature too high
2. NTC -> electronic temperature
too high.
The induction module must cool
E/3
Pan not suitable, such as loss of
magnetic properties due to the
temperature of the bottom of the pan
The pan generates working points
that are not allowed by the induction
module and that could damage parts
(such as the IGBT)
1. This error occurs after 8 seconds
and the cooking point can be used
again. If the error occurs repeatedly,
the pan must be removed.
2. If the error occurs even without
a pan, or it is a pan that normally
works, the induction module must be
replaced because it is a hardware
error.
E/4
Induction modules are not
configured (all the induction modules
can be accessed through the bus,
but no element is assigned to this
cooking point)
Induction module is not configured
1. Erase the global configuration and
re-configure.
2. Assign the induction modules
through the configuration menu.
3. If you cannot configure the
module, it must be replaced.
E/5
No communication between the UI
and the induction module
The induction module has no power
supply voltage. Incorrect connection
(cable) or induction module defective
Check connections with cables
and the power supply module; if
everything is correct, replace the
induction module
E/6
Mains fault
1. Frequency detection, mains
defective.
2. Over-voltage
Check connections with cables
and the power supply module; if
everything is correct, replace the
induction module
E/7
Unknown error
This can occur with incompatible
versions of the induction module or
Touch Control
Replace the induction module or
Touch Control
E/8
Fan error
Fan or electronic control defective
Replace the induction module
E/9
Defective induction sensor
The sensor value is invalid, defective
sensor or electronics
Replace the induction module
E/A
Hardware error
The intrinsic control has detected a
defective command component
Replace the induction module
Характеристики
Остались вопросы?Не нашли свой ответ в руководстве или возникли другие проблемы? Задайте свой вопрос в форме ниже с подробным описанием вашей ситуации, чтобы другие люди и специалисты смогли дать на него ответ. Если вы знаете как решить проблему другого человека, пожалуйста, подскажите ему :)
