Варочная панель Bertazzoni PM60 3 0 X - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
5
MAINTENANCE OF THE MACHINE
CHANGING THE PARTS
Before carrying out any maintenance work, disconnect the appliance from the gas and electric
supply.
To replace different components such as burners, taps and electrical parts you must take out the hob from
the kitchen unit by releasing the fixing hooks, unscrew the fixing screws of the burners on the work top,
unscrew the fixing nuts of the electric plates which are visible on the lower part of the hob and remove the
worktop in order to carry out the replacement of the defective parts
.
NOTE: If the taps need replacing you also need to unscrew the two fixing screws of the gas ramp at the
bottom of the hob which are found on the upper part of the latter.
For appliances equipped with automatic “ON” switches you must dismantle the “ON” switch chain before
replacing the taps.
You are advised to change the seal on the tap every time you replace a tap in order to ensure a perfect hold
between the body and ramp.
WARNING
: The electric cable which is provided with the appliance is connected to the appliance with a type
X
connection and thus can be replaced with the same type of cable as that installed without using special
tools. In the event of wear or damage to the mains cable, replace it with :
Type/ section of mains cable H05VV-F 3x0,75 mm2 or H05RR-F 3x0,75 mm2
WARNING: If you replace the electric mains cable the installer must have the earth conductor about 2
cm longer than the phase conductors and must also take heed of the warnings regarding electric
connection.
Room ventilation – Location and venting.
ATTENTION: An exhaust fan may be used with the appliance; in each case it shall be installed in
conformity with the national standards in force.
ATTENTION: Exhaust hood operation may affect other vented appliances; in each case it shall be
installed in conformity with the national standards in force.
- CHANGING THE NOZZLES FOR USE WITH OTHER TYPES OF GAS:
To change the nozzles of the burners use the following procedure:
Lift up the burners and unscrew the nozzles ( Fig. 9) using an adjustable spanner of 7 mm and change the
nozzles with those designed for the new gas supply according to the information given in TABLE A shown
below.
TABLE N°2: Adapting to different types of gas
APPLIANCE CATEGORY: III
Burner
Type of Gas
Pressure
Nozzle
Nominal Charge
Reduced Charge
Diameter
diameter
by-pass
1/100mm
mbar
1/100mm
g/h
l/h
Kw
kcal/h
kw
kcal/h
Town G110
8
145
-
227
1,00
860
0,30
258
27 reg
Auxiliary
Natural G20
20
77
-
95
1,00
860
0,30
258
27 reg
Butane G30
28
50
73
-
1,00
860
0,30
258
27
Propane
G31 37
50 71 - 1,00
860 0,30 258
27
Town G110
8
192
-
397
1,75
1505
0,44
378
31 reg
Semi-
Natural G20
20
101
-
167
1,75
1505
0,44
378
31 reg
Rapid
Butane G30
28
66
127
-
1,75
1505
0,44
378
31
Propane
G31 37
66 125 - 1,75
1505 0,44 378
31
Town G110
8
280
-
681
3
2580
0,75
645
42 reg
Natural G20
20
129
-
286
3
2580
0,75
645
42 reg
Rapid
Butane G30
28
87
218
-
3
2580
0,75
645
42
Propane
G31 37
87 214 - 3 2580 0,75 645
42
Town G110
8
130
-
181
0,8
688
0,30
258
27 reg
Dual
Natural G20
20
70
-
76
0,8
688
0,30
258
27 reg
burner
Butane G30
28
46
211
-
0,8
688
0,30
258
27
inner Propane
G31
37
46 207 -
0,8 688
0,30
258
27
Town G110
8
2x300
-
885
4,4
3784
1.8
1548
65 reg
Dual
Natural G20
20
2x110
-
419
4,4
3784
1.8
1548
65 reg
burner
Butane G30
28
2x69
298
-
4,1
3526
1.8
1548
65
outer Propane
G31
37
2x69 293 -
4,1 3526
1.8
1548
65
CAUTION: save the orifices removed from the appliance for future use
Regulation of burners
Regulation of the "MINIMUM" on the burners
To regulate the minimum on the burners carry out the following procedure indicated below:
1) Turn on the burner and put the knob onto position MINIMUM ( small flame ).
2) Remove the knob ( Fig. 10) of the tap which is set for standard pressure. The knob is found on the bar of
the tap itself.
Характеристики
Остались вопросы?Не нашли свой ответ в руководстве или возникли другие проблемы? Задайте свой вопрос в форме ниже с подробным описанием вашей ситуации, чтобы другие люди и специалисты смогли дать на него ответ. Если вы знаете как решить проблему другого человека, пожалуйста, подскажите ему :)
