VITEK VT-1762 W - Инструкция по эксплуатации - Страница 5

•  

Do not disassemble the unit yourself, if any 
malfunction is detected, address the nearest 
authorized service center.

•   Regularly clean the unit; do not allow cracks 

to appear on the sprayer.

•   Keep the unit out of reach of children.

FOR HOUSEHOLD USAGE ONLY

Using the humidifier

Unpack the unit and remove the packing materi-
als. Examine the unit for damages. Do not switch 
on the unit if there are any damages in it. Place 
the unit on the flat stable waterproof surface.

Note: 
-  if the unit was subjected to negative 

temperatures, before switching it on for the 
first time, keep it at room temperature for 30 
minutes. 

-   use the unit at temperature starting from +5 

, and relative humidity less than 80%. 

-   water temperature in the water tank (15) 

should not exceed +40°С.

1.  Take the handle (12) and remove the water 

tank (15) from the body (8).

2.  Turn over the tank (15); unscrew the lid (18), 

by turning it anti clockwise. Fill the water tank 
(15) with necessary quantity of water and 
screw the lid (18), by turning it clockwise.

Note:
-   do not fill the water tank (15) full, to avoid 

splashing of water when screwing the lid 
(18) with the filter-cartridge (17). 

3.  Set the filled tank (15) on the body of the unit 

(8). Wait for some time, which is necessary 
to fill the operating chamber of the “sprayer” 
(10) with water.

4. 

Plug in the humidifier, you will hear a sound 
signal, the indication (9) will appear on the 
display (1); the value of humidity (29, 30) will 
be displayed.

5.  Switch on the humidifier, by pressing the 

(3) “ON/OFF” button, the display will switch 
to full brightness and the steam intensity 
indication (31) will light up and the mood 
lighting (2) will switch on.

6. Press the (5) “+/-“buttons to set the 

“smog” intensity: 1, 2, 3, the corresponding 
indication (31) will appear on the display (1).

Note: 
- 

each pressing of the control buttons will be 
accompanied with a signal.

-  if no button has been pressed during 30 

seconds on the control panel or on the 
remote control, the mood lighting will go 
out, the display brightness will decrease 
automatically in 30 seconds after pressing 
any button.

7.  Press the (7) 

“NIGHT- LIGHT” button to witch 

on the mood lighting, press the 

(7) 

“NIGHT- 

LIGHT” button again, the mood lighting (2) 
will go out.

8.  To switch on the ionization mode, press the (4) 

“OZONE” button, the indication (26) will appear 
on the display (1). To switch off the ionization 
mode, press the (4) “OZONE” button once 
again, the indication (26) will go out.

9. To switch on the automatic humidity 

maintenance mode, press the (6) “SETUP” 
button, the indication “Auto” (28) will be 
flashing on the display (1), press the (5) 

“+/-“ button to set the 

required humidity in 

the room (from 45 to 90%, setting step is 
5%). In the automatic humidity maintenance 
mode the indication “Auto” (28), digital value 
of the room humidity (29) and the “smog” 
intensity (31) will appear on the display (1).  
In automatic mode “smog” output intensity 
will change and it will be reflected on the 
display (1) when the preset humidity is be 
reached, the unit will switch off, when the 
humidity decreases, the humidifier will 
switch on again. 

10. To view the preset humidity value press 

the (6) “SETUP” once, value of the preset 
humidity will appear on the display (1), in 5 
seconds the information on the display will 
return to the previous mode.

11. 

To switch off the automatic humidity 
maintenance mode, press the (6) “SETUP” 
button, press the (5) 

“+/-“button the required 

number of times

, when the humidity value 

passes 90%, the indication (28) “Auto” will 
go out.

5

              ENGLISH         

VT 1762_Instr.indd   5

VT 1762_Instr.indd   5

22.06.2011   17:22:57

22.06.2011   17:22:57