VITEK VT-1260 OG - Инструкция по эксплуатации - Страница 6

6

 ENGLISH

• Set the temperature control (7) to the re-

quired ironing temperature: “•”, “••”, “•••” 
or “MAX”, depending on the type of fabric, 
the indicator in the temperature control (7) will 
light up.

•  When the soleplate temperature (5) reaches 

the desired temperature value, the indicator 
will go out.

Note:  While steam ironing set the tempera-
ture to steam using zone, 

“•••” or “MAX”,

WATER SPRAYER

• You can dampen the fabric by pressing the 

spray button (2) several times (pic. 4).

•  Make sure that there is enough water in the 

water tank.

DRY IRONING

•  Place the iron on the base (8). 
• Set the constant steam supply control (3) 

to the “

” position (steam supply is off). 

(pic.5.1)

• Set the temperature control (7) to the re-

quired ironing temperature: “•”, “••”, “•••” 
or “MAX”, depending on the type of fabric, 
the indicator in the temperature control (7) will 
light up.

•  When the soleplate temperature (5) reaches 

the desired temperature value, the indicator 
will go out, you can start ironing.

• After you finish ironing set the temperature 

control (7) to the 

“

MIN” position.

•  Pull the plug out of the socket and let the iron 

cool down completely.

STEAM IRONING 

(pic.5)

For steam ironing set the temperature control to 
steam using zone “•••” or “MAX”.
The iron has an anti-drip valve, which stops wa-
ter supply, when the sole temperature is too low 
it prevents the appearance of drops out of the 
soleplate openings (5). While heating or cooling 
down of the sole (5), you will hear clicks of open-
ing/closing of the anti-drip valve; it means that 
the valve works normally.
•  Make sure that there is enough water in the 

water tank.

•  Place the iron on the base (8). 
• Set the constant steam supply control (3) 

to the “

” position (steam supply is off). 

(pic.5.1)

•  Insert the power plug into the socket.
•  Set the temperature control (7) to the required 

ironing temperature: to steam using zone 
“•••” or “MAX”, the indicator in the tempera-
ture control (7) will light up. 

•  When the soleplate temperature (5) reaches 

the desired temperature value, the indicator 
will go out, you can start ironing.

•  Turn the constant steam supply regulator (3) 

to set the intensity of steaming, steam will 
start outgoing from the openings of the sole-
plate (5). (pic.5.2.)

•  After you finish ironing set the (7) temperature 

control to the 

“

MIN” position and the constant 

steam supply control (3) to the “

” position 

(steam supply is off)

.

•  Pull the plug out of the socket and let the iron 

cool down completely.

•  Open the filling opening lid (9), turn over the 

unit and drain the remaining water (10). Close 
the lid (9) (pic.9).

AT TENTION!

If during the operation steam is not constantly 
supplied, check whether the temperature con-
trol (7) is set properly and whether there is water 
in the water tank.

ADDITIONAL steam supply

Additional steam supply function is useful when 
ironing folds and can only be used at high ironing 
temperatures (when the iron temperature control 
(7) is set to “•••” or “MAX”).
When the additional steam supply button (1) is 
pressed, steam will be vigorously released from 
the openings in the iron soleplate (pic.6).

Note: 
In order to avoid leakage of water from steam 
openings, press the additional steam supply 
button (1) with a 4-5 sec. interval.

VERTICAL STEAMING

For vertical steaming can be used only when the 
high temperature mode is used (set the temper-
ature control (7) to the “•••” or “MAX” position.
Hold the iron vertically at the distance 15-30 cm 
from the clothes  press the additional steam sup-
ply button (1) with a 4-5 seconds interval, steam 
will be released from the openings in the iron 
soleplate (5) (pic. 7).

1260.indd   6

1260.indd   6

24.08.2010   10:02:31

24.08.2010   10:02:31