Braun SI 8530 - Инструкция по эксплуатации - Страница 8

8

Our products are engineered to meet the 
highest standards of quality, functionality and 
design. We hope you enjoy your new Braun 
steam iron.
Notice: Remove the label, if any, from the 
sole plate before first use.

Important Safeguards

•

Before using the iron, read the use instruc-
tions completely. Keep the use instructions 
during the entire life of the iron.

•

Make sure your voltage corresponds to 
the voltage printed on the iron. Connect 
the iron to alternating current only.

•

Always unplug the iron before filling with 
water. Always pull the plug, not the cord. 
The cord should never come in contact 
with the hot objects or the sole plate.

•

Never immerse the iron in water or other 
liquids.

•

During ironing pauses, always place the 
iron upright on its heel rest. Unplug it 
when leaving the room, even if only for a 
short time.

•

Keep the iron away from children, 
especially when using the «jet» function. 
Electric irons combine high temperatures 
and hot steam that could lead to burns.

•

Never iron or dampen clothes while 
wearing them.

•

Check the cord regularly for possible 
damage.

•

If the appliance (including cord) shows 
any defect, stop using it and take it to a 
Braun Service Centre for repair.

•

Faulty or unqualified repair work many 
cause accidents or injury to the user.

•

Braun electric appliances meet applicable 
safety standards.

A Description

1 «jet» of steam openings
2 Water tank opening
3 Spray nozzle
4 Power shot button
5 2-function button: spray/«jet» of steam
6 Steam regulator
7 Steam plus button
8 Pilot light
9 Temperature selector

B Before starting off

•

This iron is designed for tap water. 
If you have extremely hard water, we 
recommend to use a mixtur of 50 % tap 
water and 50 % distilled water. Fill the 
water tank to «max» marking. Never use 
distilled water exclusively. Do not add any 
additives (e.g. starch).

•

Keep the iron in the upright position and 
connect it to the mains. Select the tem-
perature according to the ironing guide on 
the heel rest of the iron or on the label in 
your garments.

•

The pilot light goes off when the desired 
temperature is reached (after approx. 
1 

ó

 min.).

D Automatic shut-off 

The auto-off mechanism causes a slight 
rattling noise during ironing. This is  normal 
and in no case indicates a fault of the iron.
The «auto-off» pilot light will flash when 
the automatic shut-off is activated.
This happens when the iron has rested …
– horizontally on its sole plate for about

30 seconds or

– vertically on its heel rest for about

15 minutes.

C Ironing

 Vario 

steam

You can increase and reduce the 
quantity of steam by turning the steam 
regulator. The steam regulator and the 
temperature selector have to be set 
within the red range.
We recommend a medium steam 
setting for all normal ironing. Only when 
ironing linen, thick cotton or similar 
fabrics we recommend the maximum 
steam setting.

Notice: While ironing, do not turn the 
steam regulator beyond the red range. 
For extra steam, power shot and «jet» of 
steam, the temperature selector must 
be set within the continuous red range. 
These functions can even be activated 
when dry ironing.

Vario plus steam

(not model 8520)
Press the steam plus button (7) for max. 
3 seconds, but not more often than 4 
times per minute.

 Power 

shot

Press the power shot button (4) in 
intervals of at least 5 seconds.

Frontal «jet» of steam

Turn the 2-function button (5) to «jet» as 
far as it will go, then press it in intervals 
of min. 5 seconds.

 Spray 

function

Turn the 2-function button (5) to the 

symbol and press.

 Dry 

ironing

Set the steam regulator on position «0» 
(= steam off).

Notice: Prior to ironing, press the power 
shot and «jet» buttons 3 to 4 times to 
activate them. These functions can be 
used for steaming hanging clothes.

English