ASUS RP-AC53 - Инструкция по эксплуатации

Quick Start Guide

RP-AC53

Dual-band Wireless Repeater

E11934
Second Edition
August 2016

1.  Power LED

On

:  RP-AC53 is plugged to a power outlet and 

powered on.

Off

:  RP-AC53 is unplugged from a power 

outlet or powered off.

2.  Etherenet LED
 On: 

Ethernet is connected.

 Off: 

Ethernet cable is disconnected.

3.  2.4 GHz / 5 GHz Wi-Fi LED

Green : 

Best 2.4 GHz / 5 GHz Wi-Fi Repeater 

connection with parent AP.

 Orange: 

Good 2.4 GHz / 5 GHz Wi-Fi repeater 

connection with parent AP.

 Red: 

Poor 2.4 GHz / 5 GHz Wi-Fi Repeater 

connection with parent AP. 

 Off: 

Disconnected from parent AP.

Quick Setup with WPS (Wi-Fi Protected Setup)
For router/Access Point(AP) with WPS support

3

Place in an ideal location

After placing your RP-AC53 in an ideal location, RP-AC53 connects to your router/AP in about one (1) minute.

NOTES:

•   Place your RP-AC53 between your 

router/AP and wireless device to get 

the best extender performance.

•    Place your RP-AC53 in a location 

where you can get green or orange 

Wi-Fi LED.

IMPORTANT! 

 We recommend that you place your RP-AC53 in open or spacious location.

Enjoy!

1

2

Frequently Asked Questions (FAQ)

Q1:  What should I do if my router does not support WPS?

A1:

You can use Method Two to set up RP-AC53.

Q2:  How do I reset RP-AC53?

A2:  Press the RESET button on the side of RP-AC53 for about five (5) sec-

onds until the LEDs blink slowly.

Q2:  What should I do when only one band Wi-Fi LED is on?

A2:  When you are connecting to a dual-band router but only 2.4 GHz or 5 GHz Wi-Fi 

LED is on, press the WPS button on both the router and the RP-AC53 again and 

check that both 2.4 GHz and 5 GHz Wi-Fi LEDs are on.

Q4:  What should I do if RP-AC53 web interface is not accessible?

A4:

You can do any of the following:

•    Connect your computer and RP-AC53 using an Ethernet cable, and 

connect to RP-AC53’s SSID or network name. 

•    Set up your computer to obtain an IP address automatically.

•    On a web browser, ensure that you correctly enter the web address 

http://repeater.asus.com

Method One

Your RP-AC53’s wireless network name (SSID) chang-

es to your existing Wi-Fi network name, ending with 

_RPT

 or 

_RPT5G

 and shares your router/AP’s Wireless 

Password.

Power On

Place your RP-AC53 near your router/AP and plug it to a 

power outlet.

Press the power switch to ON. Wait 

until the power LED turns solid green 

and Wi-Fi LEDs stop blinking, indicating 

that RP-AC53 is ready to connect to the 

parent AP.

Connect via WPS (Wi-Fi Protected Setup)

1.   Press the WPS button on your 

Router/AP.

2.   Press the WPS button on your RP-AC53 for 

more than five (5) seconds until the LEDs 

start to blink.

NOTE:

 Ensure that your router/AP supports WPS. Otherwise, use Method TWO.

The LEDs flash about two 

(2) minutes and turn solid 

green. The color of the 

LED indicates the Wi-Fi 

signal strength.

E11934_RP-AC53_QSG_Special_V2.indd   1

2016-08-19   16:20:19