SKIL F0150731RA - Инструкция по эксплуатации - Страница 9

9

Line trimmer 

0731

INTRODUCTION

•  This tool is intended for the cutting of grass and weeds 

under bushes as well as on slopes and edges that can 
not be reached with a lawn mower

•  This tool is not intended for professional use

•  Check whether the packaging contains all parts as 

illustrated in drawing 

9

•  When parts are missing or damaged, please contact your 

dealer

•  Read this instruction manual carefully before use 

and save it for future reference 

2

•  Pay special attention to the safety instructions and 

warnings; failure to follow these may result in 

serious injury

TECHNICAL DATA 

1

TOOL ELEMENTS 

0

A

  Guide handle

B

  Knob for adjusting guide handle

C

  Cutting guard

D

  Cord restraint

E

  Lower tube

F

  Unlocking button

G

  Trigger switch

H

  Flower guard

J

  Line cutting blade

k

  Spool cap

L

  Ventilation slots

M

  Storage rail (

screws not supplied

)

N

  Storage hook

SAFETY

SPECIFIC SAFETY INSTRUCTIONS FOR LINE 

TRIMMERS

GENERAL

•  Be familiar with the controls and the proper use of the tool

•  The user is responsible for accidents or hazards 

occurring to other people or their property

•  Only use the tool when the ambient temperature is 

between 0°C and 40°C

•  Never mount metal cutting elements onto this tool

PERSONAL SAFETY

•  This tool is not intended for use by persons (including 

children) with reduced physical, sensory or mental 

capabilities, or lack of experience and knowledge, unless 

they have been given supervision or instruction 

concerning use of the tool by a person responsible for 

their safety

•  Ensure that children do not play with the tool

•  Never allow children or people who are not familiar with 

the operating instructions to use the tool

•  Keep your fingers away from the line cutting blade 

integrated in the cutting guard

•  Keep hands and feet away from the cutting lines while 

trimming, especially when switching on the tool

•  Always wear eye protection, long trousers and sturdy 

shoes when operating the tool

•  Never operate the tool in the direct vicinity of persons; 

stop using the tool when persons (especially children) or 

pets are nearby

•  Never operate the tool when you are tired, sick or under 

the inluence of alcohol or other drugs

ELECTRICAL SAFETY

•  Always check that the supply voltage is the same as the 

voltage indicated on the nameplate of the tool (tools with 

a rating of 230V or 240V can also be connected to a 

220V supply)

•  Inspect the cord periodically and have it replaced by a 

qualiied person, if damaged

•  Inspect the extension cord periodically and replace it, if 

damaged (

inadequate extension cords can be 

dangerous

)

•  Only use an extension cord which is intended for outdoor 

use and equipped with a watertight plug and coupling-
socket

•  Use completely unrolled and safe extension cords with a 

capacity of 16 Amps (U.K. 13 Amps)

•  When operating the tool use a residual current device 

(RCD) with a triggering current of 30 mA maximum

•  Do not run over, crush or pull the (extension) cord

•  Protect the (extension) cord from heat, oil and sharp 

edges

•  Keep the (extension) cord away from the rotating 

cutting lines

•  Always switch of tool and disconnect plug from power 

source if the power supply cord or the extension cord is 

cut, damaged or entangled (

do not touch the cord 

before disconnecting the plug

)

BEFORE USE

•  Only use the tool in daylight or with appropriate artiicial 

lighting

•  Check the functioning of the tool before each use and 

after any impact; in case of a defect, have it repaired 

immediately by a qualiied person (never open the tool 

yourself)

•  Before use, thoroughly inspect the cutting area and 

remove any object that the tool may sling during cutting 

(such as stones, loose pieces of wood, etc.)

DURING USE

•  Never use the tool when cord is damaged; have it 

replaced by a qualiied person

•  Never operate the tool with a damaged cutting guard or 

without the cutting guard mounted

•  The cutting lines continue to rotate for a short time 

after the tool is switched off

•  Do not cut grass which is not on the ground (e.g. on walls 

or rocks)

•  Do not cross roads or gravel paths with the tool still 

running

•  Do not get distracted and always concentrate on what 

you are doing

•  Always disconnect plug from power source

-  whenever leaving the tool unattended

-  before clearing jammed material

-  before checking, cleaning or working on the tool