Электрический коса SKIL F0150739RA - Инструкция по эксплуатации - Страница 18

18

• 

Storage 

s

-

store the tool 

indoors

 in a dry and locked-up place, 

out of reach of children

-

securely mount storage rail Z on the wall with 4 screws 

(

not supplied

) and horizontally leveled

• 

If the tool should fail despite the care taken in 

manufacturing and testing procedures, repair should 

be carried out by an after-sales service centre for SKIL 

power tools

-

send the tool 

undismantled

 together with proof of 

purchase to your dealer or the nearest SKIL service 

station (addresses as well as the service diagram of 

the tool are listed on www.skil.com)

TROUBLESHOOTING

• 

The following listing shows problem symptoms, possible 

causes and corrective actions (if these do not identify 

and correct the problem, contact your dealer or service 

station)

!

switch of the tool and disconnect the plug before 

investigating the problem

/

  Tool does not operate

-

power supply socket faulty -> use another socket

-

extension cord damaged -> replace extension cord

/

  Tool operates intermittently

-

internal wiring defective -> contact dealer/service 

station

-

on/of switch defective -> contact dealer/service 

station

/

  Tool vibrates abnormally

-

grass/brushwood too high -> cut in stages

/

  Tool does not cut

-

line too short/broken of -> feed the line manually

/

  Line cannot be fed

-

spool empty -> replace spool

-

line entangled inside spool -> inspect spool; rewind if 

necessary

/

  Line keeps breaking

-

line entangled inside spool -> inspect spool; rewind if 

necessary

-

trimmer incorrectly used -> only trim with the tip of the 

line; avoid stones, walls and other hard objects; feed 

the line regularly

-

press down spool irmly into spool cap XY and mount 

button T onto the spool by turning it clockwise until it 

comes to a complete stop

!

ensure that the spool is located securely in place, 

then release both lines from slots X by pulling 

them irmly

• 

Replacing spool 

p

!

switch of the tool and disconnect the plug

-

simply remove/mount old/new spool as illustrated

-

only use SKIL spool 2610Z06653 with this tool 

(

damage due to using other spools will be 

excluded from the warranty

)

-

after replacing the spool test-run the tool for at least 

one minute without load to ensure that the tool is 

operating properly

!

be sure tool is switched of when plugging in

WHEN USING TOOL AS BRUSH CUTTER

• 

Application advice

!

do not use the cutting blade in the vicinity of 

solid obstacles -> danger of kickback/personal 

injury

!

for safety purposes always approach the 

brushwood from the left to the right

-

cut high brushwood in layers (always start from the 

top)

• 

Reversing/changing cutting blade 

a

-

the cutting blade has cutting edges on both sides; 

reverse the blade, when one side has become blunt

-

replace the cutting blade when both sides are blunt

!

switch of the tool and disconnect the plug

-

remove/mount old/new cutting blade as illustrated

-

only use SKIL cutting blade 2610Z06654 with this tool 

(

damage due to using other cutting blades will be 

excluded from the warranty

)

-

after replacing the cutting blade test-run the tool for at 

least one minute without load to ensure that the tool is 

operating properly

!

be sure tool is switched of when plugging in

-

when necessary, have the cutting blade sharpened by 

a specialist

MAINTENANCE / SERVICE

• 

This tool is not intended for professional use

• 

Regularly check the condition of the cutting mechanism 

and the tightness of nuts, bolts and screws

• 

Regularly check for worn or damaged components and 

have them repaired/replaced when necessary

•  Always disconnect plug from power source before 

cleaning and/or maintenance

• 

Always keep tool and cord clean (especially the 

ventilation slots)

-

clean the tool with a damp cloth (do not use cleaning 

agents or solvents)

-

clean line cutting knife V 

2

 and cutting guard C 

2

after each use

-

clean ventilation slots W 

2

 regularly with a brush or 

compressed air