Триммеры Greenworks GD60BCB 60V 2108407 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
•
Cut tall grass from the top down.
If grass winds around the trimmer head:
•
Remove the battery pack.
•
Remove the grass.
4.7
CUTTING TIPS
Figure 8.
•
Tilt the machine toward the area to be cut. Use the tip of
the cutting line to cut grass.
•
Move the machine from right to left to prevent thrown
debris toward the operator.
•
Do not cut in the dangerous area.
•
Do not force the trimmer head into uncut grass.
•
Wire and picket fences cause cutting line wear and
breakage. Stone and brick walls, curbs, and wood can
wear the cutting line quickly.
4.8
ADJUST THE LENGTH OF THE
CUTTING LINE
Figure 9.
While you operate the machine, the cutting line gets worn and
shorter. You can adjust the length of the cutting line.
1. Hit the trimmer head against the ground while you
operate the machine.
2. Line is automatically released and the cut-off blade cuts
the excess length.
4.9
LINE CUT-OFF BLADE
Figure 10.
This trimmer is equipped with a line cut-off blade on the
guard. The line cut off blade continuously trims the line to
ensure a consistent and efficient cut diameter. Advance line
whenever you hear the engine running faster than normal, or
when trimming efficiency diminishes. This will maintain best
performance and keep line long enough to advance properly.
4.10 ADJUST THE CUTTING
DIAMETER
Figure 10.
NOTE
The machine is set at a 35.6 cm cutting diameter. You can
adjust to a 40.6 cm cutting diameter.
Set the cutting diameter to 35.6 cm for greater runtime and
40.6 cmfor a larger cutting area.
1. Remove the battery pack.
2. Remove the blade screws from the cut-off blade.
3. Turn the cut-off blade 180°.
4. Tighten the blade screws.
5
MAINTENANCE
IMPORTANT
Read and understand the safety regulations and the
maintenance instructions before you clean, repair or do the
maintenance work on the machine.
IMPORTANT
Make sure that all nuts, bolts and screws are tight. Examine
regularly that you install the handles tightly.
IMPORTANT
Use only the replacement parts and accessories of the initial
manufacturer.
5.1
GENERAL INFORMATION
IMPORTANT
Only your dealer or approved service center can do the
maintenance that is not given in this manual.
Before the maintenance operations:
•
Stop the machine.
•
Remove the battery pack.
•
Cool the motor.
•
Store the machine in cool and dry place.
•
Use correct clothing, protective gloves and safety glasses.
5.2
CLEAN THE MACHINE
•
Clean the machine after use with a moist cloth dipped in
neutral detergent.
•
Do not use aggressive detergents or solvents to clean the
plastic parts or handles.
•
Keep the trimmer head free of grass, leaves, or excessive
grease.
•
Keep the air vents clean and free of debris to avoid
overheating and damage to the motor or the battery.
•
Do not spray water onto the motor and electrical
components.
5.3
REMOVE ANY REMAINING LINE
Figure 11 - 13.
1. Push the tabs on the sides of the trimmer head at the same
time.
2. Remove the spool cover and the spool.
3. Remove any remaining line.
4. Put the spool in the spool housing.
5. Install the spool cover onto the trimmer head.
6. Push the spool cover until it clicks into position.
6
English
EN
