Einhell PXC GC-CT 18/24 - Инструкция по эксплуатации - Страница 24

GB

- 24 -

All LEDs 

fl

 ash:

The battery pack has undergone exhaustive di-

scharge and is defective. Do not use or charge a 

defective battery pack.

6. Operation

To obtain maximum performance from your grass 

trimmer, please follow these instructions:

• 

Never use the grass trimmer without the 

guard.

• 

Do not mow grass when it is wet. The best 

results are achieved with dry grass.

• 

To switch on your grass trimmer, press the 

ON/OFF switch (Fig. 11/Item 1).

• 

To switch off your grass trimmer, let go of the 

On/Off switch again (Fig. 11/Item 1).

• 

Do not allow the grass trimmer near the grass 

until the switch is pressed, i.e. the grass trim-

mer is in operation.

• 

To cut properly, swing the machine sideways 

while moving forwards. Keep the grass trim-

mer inclined at an angle of approx. 30° while 

you do so (see Figs. 15 and 16).

• 

If the grass is long, the grass must be cut 

shorter in stages, starting from the tip (see 

Fig. 17).

• 

Use the guard hood to prevent unnecessary 

wear.

• 

To avoid unnecessary wear, keep the grass 

trimmer away from hard objects.

• 

To use the edge guide along walls or objects, 

swing the edge guide forward to the front (Fig. 

18). Swing it up when not in use (Fig. 19).

7.  Cleaning, maintenance and 

ordering of spare parts

Danger! 

Before putting away or cleaning the grass trim-

mer, switch o

ff

  and remove the battery pack.

7.1 Cleaning

• 

Keep all safety devices, air vents and the 

motor housing free of dirt and dust as far as 

possible. Wipe the equipment with a clean 

cloth or blow it down with compressed air at 

low pressure. 

• 

We recommend that you clean the equipment 

immediately after you use it.

• 

Clean the equipment regularly with a damp 

cloth and some soft soap. Do not use 

cleaning agents or solvents; these may be ag-

gressive to the plastic parts in the equipment. 

Ensure that no water can get into the interior 

of the equipment. The ingress of water into an 

electric tool increases the risk of an electric 

shock.

• 

Use a brush to remove deposits from the 

safety guard.

7.2  Replacing the blade

Danger! Be sure to remove the battery pack 

before replacing!

• 

Push the blade to the inside (Fig. 20) and re-

move it through the larger opening.

• 

To fit the new blade, proceed in reverse order 

(Fig. 10). Make sure the blade locks into place 

correctly as shown in Fig. 20.

7.3 Maintenance

There are no other parts inside the equipment 

which require maintenance.

7.4  Ordering spare parts

Please provide the following information on all 

orders for spare parts:

• 

Model/type of the equipment

• 

Article number of the equipment

• 

ID number of the equipment

• 

Spare part number of the required spare part

For our latest prices and information please go to 

www.isc-gmbh.info

8.  Disposal and recycling

The equipment is supplied in packaging to pre-

vent it from being damaged in transit. The raw 

materials in this packaging can be reused or 

recycled. The equipment and its accessories are 

made of various types of material, such as metal 

and plastic. Defective components must be dispo-

sed of as special waste. Ask your dealer or your 

local council.

9. Storage

Store the equipment and accessories in a dark 

and dry place at above freezing temperature. The 

ideal storage temperature is between 5 and 30 

°C. Store the electric tool in its original packaging.

Anl_GC_CT_18_24_Li_Solo_SPK9.indb   24

Anl_GC_CT_18_24_Li_Solo_SPK9.indb   24

19.10.2017   13:03:28

19.10.2017   13:03:28