Коса DEWALT FLEXVOLT 54 В BRUSHLESS DCMAS5713X1-QW - Инструкция по эксплуатации - Страница 9

7

English

charger as battery pack may rupture causing serious 
personal injury.

•  Charge the battery packs only in 

D

e

WALT

 chargers.

• 

DO NOT 

splash or immerse in water or other liquids.

• 

Do not store or use the tool and battery pack in locations 
where the temperature may fall below 4 ˚C (39.2 ˚F) 
(such as outside sheds or metal buildings in winter), or 
reach or exceed 40 ˚C (104 ˚F) (such as outside sheds or 
metal buildings in summer).

• 

Do not incinerate the battery pack even if it is severely 
damaged or is completely worn out.

 The battery pack can 

explode in a fire. Toxic fumes and materials are created when 
lithium‑ion battery packs are burned.

• 

If battery contents come into contact with the skin, 
immediately wash area with mild soap and water. 

If 

battery liquid gets into the eye, rinse water over the open eye 
for 15 minutes or until irritation ceases. If medical attention 
is needed, the battery electrolyte is composed of a mixture of 
liquid organic carbonates and lithium salts.

• 

Contents of opened battery cells may cause respiratory 
irritation. 

Provide fresh air. If symptoms persists, seek 

medical attention.

WARNING: 

Burn hazard. Battery liquid may be flammable 

if exposed to spark or flame.

WARNING: 

Never attempt to open the battery pack for 

any reason. If battery pack case is cracked or damaged, 
do not insert into charger. Do not crush, drop or damage 
battery pack. Do not use a battery pack or charger that 
has received a sharp blow, been dropped, run over or 
damaged in any way (i.e., pierced with a nail, hit with 
a hammer, stepped on). Electric shock or electrocution 
may result. Damaged battery packs should be returned to 
service centre for recycling.

WARNING: Fire hazard. Do not store or carry the 
battery pack so that metal objects can contact 
exposed battery terminals. 

For example, do not place 

the battery pack in aprons, pockets, tool boxes, product kit 
boxes, drawers, etc., with loose nails, screws, keys, etc.

CAUTION:

When not in use, place tool on its side on 

a stable surface where it will not cause a tripping 
or falling hazard. 

Some tools with large battery packs 

will stand upright on the battery pack but may be easily 
knocked over.

Transportation

WARNING: Fire hazard. 

Transporting batteries can 

possibly cause fire if the battery terminals inadvertently 
come in contact with conductive materials. When 
transporting batteries, make sure that the battery 
terminals are protected and well insulated from 
materials that could contact them and cause a short 
circuit. 

NOTE: 

Lithium‑ion batteries should not be put in 

checked baggage.

D

e

WALT

 batteries comply with all applicable shipping 

regulations as prescribed by industry and legal standards which 
include UN Recommendations on the Transport of Dangerous 

Battery Packs

Important Safety Instructions for All 
Battery Packs

When ordering replacement battery packs, be sure to include 
catalogue number and voltage.
The battery pack is not fully charged out of the carton. Before 
using the battery pack and charger, read the safety instructions 
below. Then follow charging procedures outlined.

READ ALL INSTRUCTIONS

• 

Do not charge or use battery in explosive atmospheres, 
such as in the presence of flammable liquids, gases or 
dust. 

Inserting or removing the battery from the charger may 

ignite the dust or fumes.

• 

Never force battery pack into charger. Do not modify 
battery pack in any way to fit into a non‑compatible 

hot/Cold Pack Delay

When the charger detects a battery pack that is too hot or too 
cold, it automatically starts a Hot/Cold Pack Delay, suspending 
charging until the battery pack has reached an appropriate 
temperature. The charger then automatically switches to the 
pack charging mode. This feature ensures maximum battery 
pack life.
A cold battery pack will charge at a slower rate than a warm 
battery pack. The battery pack will charge at that slower rate 
throughout the entire charging cycle and will not return to 
maximum charge rate even if the battery pack warms.

Electronic Protection system

XR Li‑Ion tools are designed with an Electronic Protection 
System that will protect the battery pack against overloading, 
overheating or deep discharge.
The tool will automatically turn off if the Electronic Protection 
System engages. If this occurs, place the lithium‑ion battery 
pack on the charger until it is fully charged.

Wall Mounting

These chargers are designed to be wall mountable or to sit 
upright on a table or work surface. If wall mounting, locate the 
charger within reach of an electrical outlet, and away from a 
corner or other obstructions which may impede air flow. Use 
the back of the charger as a template for the location of the 
mounting screws on the wall. Mount the charger securely using 
drywall screws (purchased separately) at least 25.4 mm long 
with a screw head diameter of 7–9 mm, screwed into wood to 
an optimal depth leaving approximately 5.5 mm of the screw 
exposed. Align the slots on the back of the charger with the 
exposed screws and fully engage them in the slots.

Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger 
from the AC outlet before cleaning

. Dirt and grease 

may be removed from the exterior of the charger using a 
cloth or soft non‑metallic brush. Do not use water or any 
cleaning solutions. Never let any liquid get inside the tool; 
never immerse any part of the tool into a liquid.