Decker GLC1423L - Инструкция по эксплуатации - Страница 8

8

ENGLISH

(Original instructions)

Use

Warning!

 Let the tool work at its own pace. Do not overload.

easily done before. The battery may become warm while 

charging; this is normal and does not indicate a problem.

Warning!

 Do not charge the battery at ambient temperatures 

below 10 °C or above 40 °C. Recommended charging 

temperature: approx. 24 °C.

Note: The charger will not charge a battery if the cell 

temperature is below approximately 10 °C or above 40 °C.

The battery should be left in the charger and the charger 

will begin to charge automatically when the cell 

temperature warms up or cools down.

u

  To charge the battery (4), insert it into the charger (19). 

force. Be sure that the battery is fully seated in the 

charger.

u

  Plug in the charger and switch on at the mains.

The charging indicator (20) will blink.

The charge is complete when the charging indicator (20) 

switches to continuously on. The charger and the battery can 

charger occasionally tops up the battery charge.

u

  Charge discharged batteries within 1 week. Battery life will 

be greatly diminished if stored in a discharged state.

Leaving the battery in the charger

The charger and battery pack can be left connected with the 

pack fresh and fully charged.

Setting the tool to trimming or edging mode  

edging mode to trim overhanging grass along lawn edges and 

For trimming, the trimmer head should be in the position 

u

  Disconnect the tool from the supply.

u

  Loosen the adjustment collar (6) by turning it clockwise.

u

  Whilst holding the handle (2), rotate the head (8) 

clockwise.

u

  Tighten the collar (6) by turning it anti-clockwise.

u

  Slide the edge guide (9) into the motor housing.

Note:

 Note: The head will only rotate in one direction.

For edging, the trimmer head should be in the position shown 

u

  Disconnect the tool from the supply.

u

  Loosen the adjustment collar (6) by turning it clockwise.

u

  Whilst holding the handle (2), rotate the head (8) 

anti-clockwise.

u

  Tighten the collar (6) by turning it anti-clockwise.

u

  Slide the edge guide out of the motor housing. Ensure that 

the edging guide (9) is fully extended, an audible click will 

be heard.

Note:

 The head will only rotate in one direction.

Switching on and off 

u

  To switch the tool on, press in and hold the lock off button 

(3) then squeeze the trigger lever (1). Once the tool is 

running you may release the lock off button (3).

u

  To switch the tool off, release the trigger lever.

Warning!

 Never attempt to lock the trigger lever in the on 

position.

Hints for optimum use

General

u

  In order to achieve optimum cutting results, only cut dry 

grass.

Trimming

u

u

  Gently swing the trimmer from side to side.

u

  When cutting long grass, work in stages from the top. Take 

small cuts.

u

  Keep the tool away from hard objects and delicate plants.

u

  Cutting line will wear faster and require more feeding if the 

cutting is done along pavements or other abrasive 

surfaces or heavier weeds are being cut.

u

  If the tool starts running slowly, reduce the load.

Edging

Optimum cutting results are achieved on edges deeper than 

50 mm.

u

  Do not use the tool to create edges. To create edges,

use an edging spade.

u

u

  To make a closer cut, slightly tilt the tool.

Replacement spools of cutting line are available from your 

BLACK+DECKER dealer (cat. no. A6481-XJ). 

u

  Unplug the tool.

u

  Keep the tabs (21) depressed and remove the spool cover 

(22) from the housing (7).

68

Downloaded from 

www.Manualslib.com

manuals search engine