Aresa AR-4002 - Инструкция по эксплуатации - Страница 6

• Do not let the cord hang over the edge of the table or over hot surfaces.

• Unplug the appliance if it is not in use, or before cleaning.

• Do not use the appliance for purposes other than those specified in the instruction manual.

• Be extremely careful when children are near the appliance.

• Attention! The appliance heats up during operation!

• Do not block the steam outlet. Beware of hot steam!

• Do not place the appliance close to furniture, walls, or electrical switches. When the device is operated, steam will escape from it.

• Do not place ice cubes in the appliance to avoid condensation on the appliance, which may cause an electric short circuit.

• Do not store food in the appliance.

• When spilling hot water, be careful not to burn yourself.

• If you want to drain the water, open the lid.

• The thermo

pot

 is designed only for boiling water. Do not boil milk, wine and other liquids. Foam arising from boiling can block the steam outlet opening. This also

 causes the rapid formation of scale.

• Do not cover the thermo

pot

 with a cloth and / or a towel during operation.

• Move the heatpump only by the handle.

• Do not operate the device with wet hands.

ENGLISH

• Do not press the cover opening lever while carrying.

• Unplug the unit after use and before cleaning. Before moving, carrying out cleaning or other maintenance operations, allow the unit to cool.

• If you do not use the appliance, turn it off. While turning off the device, do not pull on the power cord, gently pull the plug from the outlet.

• The device can only be connected to a grounded network. To ensure your safety, grounding must comply with the established electrical codes.

• This appliance is intended for household use only.

• When using an extension cord, make sure that the maximum permissible cable power corresponds to the power of the device.

• Keep th

is

 instruction

 manual

.

The manufacturer reserves the right, without additional notice, to make minor changes to the design of the product that do not radically affect its safety, performance and 

functionality.

     OPERATION

• Open the lid of the thermopot. To open the lid, pull the lever (10).

• Fill 

in 

the inner pot  with water using a kettle, jug or other container. Do not allow

water to enter the 

housing.

• After filling the pot with water, close the lid until it clicks.

• Connect the device to the mains.

• The boiling cycle starts. The corresponding indicator on the front panel (boiling) lights up.

FIRST USAGE

Unpack the device and remove all labels. Before using the appliance for the first time, check that the power supply of your appliance 

corresponds to the power supply in your network.

Fill 

in 

the thermopot with water and boil it. Drain the water with a manual pump. Repeat the procedure 2-3 times. Your appliance is ready for use.

     TEMPERATURE MAINTENANCE FUNCTION

After the water boils, the device automatically goes into the temperature maintenance mode, while the indicator for maintaining the 

temperature lights up.

Water can be supplied only if it is in the heating 

mode

 (the heating indicator is on). Place a cup under the water spout (4).

For this model, there are 3 ways to supply water:

1st 

way

 - press the cup on the lever (3), located behind the spout (4);

2nd 

way

 - press the water supply button (5);

The third way is to press the water supply pump on the lid (7).

 To lock the water pump, place the pump lock (8) in the appropriate position (see photo)

WATER SUPPLY AND BLOCKAGE

When you turn on the boiling function of the appliance with an empty water tank, it will automatically shut off from the mains. As the

temperature decreases, the boiling function automatically switches on again, so it is necessary to fill the tank in time.

SWITCH OFF FUNCTION IN CASE OF INSUFFICIENT WATER Q

U

ANTITY 

WATER SUPPLY AND BLOCKAGE

Important! For boiling it is recommended to use only water that has passed the filtration cycle with a household filter or bottled water.

FAULTS AND PROCESSING METHODS

METHOD

Connect the power cord correctly

Drain the water to or below the maximum water level

Boil and drain the water (2p)

CAUSE

The water level is above the maximum level 

FAULT

Water doesn’t heat up

Hot water flows by itself

Unusual smell from  the water 

Smell of plastic during the first use

The power cord is not plugged into the outlet or to the appliance