Stanley STXH2000 - Инструкция по эксплуатации - Страница 5

5

ENGLISH

(Original instructions)

•  Do not allow paint to adhere

 to the nozzle or scraper 

as it could ignite after a time.

•  Do not operate your heat gun 

whilst it is hanging by 

the hanging hook.

•  A fire may arise if the appliance is not used with 

care.

•  Do not place the nozzle against anything while using 

or immediately after use.

•  Do not poke anything down the nozzle as it could 

give you an electric shock.

Features (fig. A)

1. Switch
2. Heat control knob
3. Ventilation slots
4. Nozzle

Handling Your Heat Gun

Do not place your hand over the ventilation slots (3) or block 

these vents in any way. This restricts the airflow through the 

element and causes over heating.

Setting the temperature (fig. B)

•  To increase the temperature setting, turn the heat control 

knob (2) anti-clockwise.

•  To reduce the temperature setting, turn the heat control 

knob clockwise.

Operating Your Heat Gun (fig. C)

•  To switch your heat gun on at the low temperature 

setting, press the switch (1) to depress to position “I”.

•  To switch the tool on at the high temperature setting, set 

the switch (1) to position “II”.

•  To switch the tool off, set the on/off switch (1) to position 

“0”.

Note:

 Allow the element to heat up for a few seconds before

use. Initially, some smoke may emit from your heat gun. This 

is normal and will soon cease.

Cooling Down

In use, the nozzle (4) of your heat gun becomes extremely 

hot. Great care is necessary when cooling your heat gun 

after use.

Hands Free Use (fig. D)

This tool can also be used in stationary mode.

•  Place the tool onto a firm and stable surface as shown.
•  Always point your heat gun away from you.
•  Secure the cable to prevent pulling your heat gun off the 

stand.

Do not touch the nozzle (4) and ensure that 

nothing is dropped into the nozzle. Carefully 

switch off your heat gun and then allow it to cool

Paint Stripping

Your heat gun is designed to soften paint and lacquer 

enabling it to be removed using a good quality hand scraper. 

Proceed as follows: Direct the hot air onto the area to be 

removed. When the paint softens, scrape firmly. Experiment 

to establish the length of time necessary to apply the heat to 

obtain optimum results. Scrape the softened paint 

immediately or it will harden again.

Your heat gun is not suitable for stripping metal-framed 

windows. This is because the heat from the heat gun is 

conducted through the metal and can crack the glass. 

Scrape with the grain of the wood wherever possible. Do not 

linger on one spot for too long as the surface may char or 

ignite.

Accessories

The performance of your tool depends on the accessory 

used. Stanley and Piranha accessories are engineered to 

high quality standards and designed to enhance the 

performance of your tool. By using these accessories you 

will get the very best from your tool.

Read 

Instructions 

Manual
Use Eye 

Protection
Use Ear 

Protection

V ........   Volts         
A ........  Amperes

Hz .......  Hertz
W ........  Watts
min .....  minutes

.....  Alternating  

Current

.....  Direct  

Current 

n

0

  .......  No-Load 

Speed

 ......  Class II

Construction

....  Earthing 

Terminal

....  Safety Alert

Symbol

...

/

min..  Revolutions 

or Recipro-

cation per 

minute

Labels on tool

The label on your tool may include the following symbols:

Position of date barcode

The Date Code, which also includes the year of 

manufacture, is printed into the housing.

Example:

2014 XX JN

             Year of manufacturing