Stanley STXH2000 - Инструкция по эксплуатации - Страница 4

ENGLISH

4

(Original instructions)

h.  Use clamps or another practical way to secure and 

support the workpiece to a stable platform.

 Holding 

the work by hand or against your body leaves it unstable 

and may lead to loss of control.

Before drilling into walls, floors or ceilings check for the 

location of wiring and pipes.

Avoid touching the tip of a drill bit just after drilling, as it 

may be hot.

4.  Power tool use and care
a.  Do not force the power tool. Use the correct power 

tool for your application.

 The correct power tool will do 

the job better and safer at the rate for which it was 

designed.

b.  Do not use the power tool if the switch does not turn 

it on and off.

 Any power tool that cannot be controlled 

with the switch is dangerous and must be repaired.

c.  Disconnect the plug from the power source before 

making any adjustments, changing accessories, or 

storing power tools.

 Such preventive safety measures 

reduce the risk of starting the power tool accidentally.

d.  Store idle power tools out of the reach of children 

and do not allow persons unfamiliar with the power 

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained 

users.

e.  Maintain power tools. Check for misalignment or 

binding of moving parts, breakage of parts and any 

other condition that may affect the power tools 

operation. If damaged, have the power tool repaired 

before use.

 Many accidents are caused by poorly 

maintained power tools.

f.  Keep cutting tools sharp and clean.

 Properly 

maintained cutting tools with sharp cutting edges are 

less likely to bind and are easier to control.

g.  Use the power tool, accessories and tool bits etc., in 

accordance with these instructions and in the 

manner intended for the particular type of power 

tool, taking into account the working conditions and 

the work to be performed.

 Use of the power tool for 

operations different from those intended could result in a 

hazardous situation.

5.  Service

a.  Have your power tool serviced by a qualified repair 

person using only identical replacement parts.

 This 

will ensure that the safety of the power tool is 

maintained.

Additional Safety Instructions for Heat Guns

1)  A fire may result if the appliance is not used with care, 

therefore

  -   Do not apply to the same place for long time
  -   Do not sue in presence of an explosive atmosphere

  -   Be aware that heat may be conducted to combustible   

     materials that are out of sight

  -   Place the appliance on site after use and allow it   to   

     cool down before storage

  -   Do not leave the appliance unattended when it  

      is switched on.

•  Always switch off before putting tool down.
•  Extreme care should be taken when stripping paint,

the peelings, residue and vapors of paint may contain 

lead, which is poisonous. Once deposited on surfaces, 

hand to mouth contact can result in the ingestion of lead. 

Exposures to even low levels of lead can caused 

irreversible brain and nervous system damage; young 

and unborn children are particularly vulnerable. Do not 

smoke, eat or drink in a work area that could or may be 

contaminated by lead. 

Lead based paints should only 

be removed by a professional and should not be 

removed using a heat gun.

•  When removing paints you should ensure that your 

work area is enclosed.

 It is advisable to wear a dust 

mask.

•  Do not burn the paint.

 Keep the nozzle at least 25mm 

(1”) from the surface as this keeps the temperature 

below the required 450°C. If you are scraping from a 

vertical position then you should scrape downwards to 

prevent the paint from falling back into the heat gun and 

burning. Dispose of all paint debris safely and ensure 

that the work area is thoroughly cleaned after completing 

the job.

•  Do not use in a damp atmosphere or where 

flammable gases may be present

 or use near 

combustible materials. Spaces behind boards, ceilings 

and floors and wall cavities in timber frame constructed 

houses can contain flammable materials. Check before 

using the heat gun.

•  Allow the tool to cool fully before storing.
•  Ensure adequate ventilation

 when using heat guns as 

toxic fumes may be produced.

•  Do not use as a hairdryer!

 The air temperature is far 

higher than a hairdryer.

•  Do not obstruct

 either the air intake or nozzle outlet as 

this may cause excessive heat build up resulting in 

damage to the tool.

•  Do not direct the hot air blast at other people.
•  Do not touch the metal nozzle

 as it becomes very hot 

during use and remains hot for up to 30 minutes after 

use. Do not look down the nozzle while the unit is 

working because of the high temperatures being 

produced.