Einhell TE-SV 18 Li (2347180) - Инструкция по эксплуатации - Страница 17

GB

- 17 -

that marked on the rating plate of the battery 

charger. Insert the power plug of the charger 

(c) into the socket outlet. The green LED will 

then begin to 

fl

 ash.

3.  Insert the battery pack (b) into the battery 

charger (c).

4.  In the section entitled „Charger indicator“ you 

will 

fi

 nd a table with an explanation of the LED 

indicator on the charger.

The battery pack can become a little warm during 

the charging. This is normal.

If the battery pack fails to charge, check:

• 

 whether there is voltage at the socket outlet

• 

 whether there is good contact at the charging 

contacts

If the battery pack still fails to charge, send

• 

 the charging unit

• 

 and the battery pack

to our customer service center.

To ensure that items are properly packaged 

and delivered when you send them to us, 

please contact our customer service or the 

point of sale at which the equipment was 

purchased.

When shipping or disposing of batteries and 

cordless tools, always ensure that they are 

packed individually in plastic bags to prevent 

short circuits and 

fi

 res.

To ensure that the battery pack provides long ser-

vice, you should take care to recharge it promptly. 

You must recharge the battery pack when you 

notice that the performance of the device drops. 

Never allow the battery pack to become fully di-

scharged. This will cause it to develop a defect.

Fitting the battery (Fig. 8)

Push the battery (a) into the battery mount provi-

ded until you hear it latch in place.

Battery capacity indicator (Fig. 11b)

Press the button for the battery capacity indicator 

(a). The battery capacity indicator (Fig. d) shows 

the charge status of the battery using 3 LEDs.

All 3 LEDs are lit:

The battery is fully charged.

2 or 1 LED(s) are lit:

The battery has an adequate remaining charge.

1 LED 

fl

 ashes:

The battery is empty, recharge the battery.

All LEDs blink:

The battery temperature is too low. Remove the 

battery from the equipment, keep it at room tem-

perature for one day. If the fault reoccurs, this me-

ans that the rechargeable battery has undergone 

exhaustive discharge and is defective. Remove 

the battery from the equipment. Never use or 

charge a defective battery.

6. Operation

6.1 On/O

ff

  switch (Fig. 9)

To switch on: press the On/O

ff

  switch (2). To 

switch o

ff

 : press the On/O

ff

  switch again.

6.2  Vacuum setting switch (Fig. 9)

The equipment has 2 vacuum settings:

ECO

 - Normal suction power and motor brush 

speed for cleaning hard 

fl

 oors and short-pile car-

pets or when a longer running time is needed.

BOOST 

- High suction power and motor brush 

speed for cleaning plush carpets and when a 

higher cleaning level is needed. The equipment 

starts in ECO mode. Press the vacuum setting 

switch (17) once to switch to BOOST mode.

6.3  Emptying the container (Fig. 10)

Important! 

To achieve the best suction perfor-

mance, empty the container each time after you 

use the cleaner or as soon as the dust reaches 

the MAX line.

Position the container (4) above a waste bin. 

Press the release button (5) downwards in order 

to open the container 

fl

 ap (13). When the empty-

ing is 

fi

 nished, close the container 

fl

 ap until you 

hear it latch in place.

6.4  Cleaning the 

fi

 lter

Warning!

Switch o

ff

  the equipment and remove the bat-

tery before you carry out any maintenance and 

cleaning work.

Cleaning the 

fi

 lter

Take care not to damage the 

fi

 lter when you clean 

it. Clean the 

fi

 lter by tapping it lightly and brushing 

it with a 

fi

 ne brush.

If necessary you can clean the 

fi

 lter with a little 

soft soap under under running water and then 

allow it to air-dry.

Anl_TE_SV_18_Li_SPK13.indb   17

08.07.2021   08:40:27