Gorenje WTD 63111 - Инструкция по эксплуатации - Страница 10

19

4 / PROGRAMMING YOUR APPLIANCE

EN

18

EN

4 / PROGRAMMING YOUR APPLIANCE

• PROGRAMMING A WASH CYCLE (continued)

You can delay your cycle by pressing the

delayed Start 

but-

tons

(refer to the chapter on “OTHER FUNCTIONS”

“

Delayed Start 

”).

The display

then shows the time before the cycle starts.

(When under one hour, the time is displayed in minutes).

3

3

D

D

•Operations to perform (continued)

Display

Display

Display

min

— Turn 

the program selector

to the 

“0”

position.

NB :

Cancellation means you always have to re-program

from scratch.
If you have cancelled during washing, if you need to drain
the water, run a 

“Spin” 

program

and set a suitable

speed.

A

A

All displays are extinguished

•Cancellation during programming, washing or
during pause

NB :

After the spin, your washing machine automatically

cools the laundry and positions the drum with the opening
at the top for easier access to the laundry. This operation
lasts 3 minutes maximum.
The 

display

then shows 

“StOP”

, which tells you the

cycle has finished.
— Turn 

the program selector

to the 

“0”

position You can

then open the lid and remove your laundry.

A

A

3

3

•Indication of End of cycle

Important :

Before switching your machine on, check that the electrical power cord is connected and

the water valve is open. Ensure that the drum doors and the machine lid are properly closed.
In the "End of cycle" phase, when ”StOP” is displayed, any action on one of the control elements
(selector or buttons) lets you return to "Programming" mode.
For safety reasons, at the end of a cycle, we recommend disconnecting the power cord and shut-
ting off the water supply valve.

(The indicator

lights flash alternately)

• PROGRAMMING A WASH CYCLE WITH SUBSEQUENT DRYING

• PROGRAMMING A DRYING CYCLE ONLY

Important :

To ensure proper drying, the load must not 

exceed 4 kg.

If the machine estimates that the load is too large to permit
subsequent drying, it stops at the end of the wash cycle and
informs you via the figure 

“4” 

flashing on the 

display

. 

In this case, adjust the laundry load, and press the

“Start

/Pause” button

to resume drying.

E

E

2

2

•Operations to be perform

Display

Display

The 

"Drying"

indicator lights up.

•Operations to be perform

(The indicator for the

"Drying"

option lights up)

The time displayed includes estima-
ted drying time.

GE

Tr/min

Tip: 

To estimate the drying time, begin to choose a duration by default more than excess,

in order to avoid an over-drying of your laundry.

— Choose immediate start by pressing the 

“Start

/Pause”

button

...

The 

cycle sequence indicator 

lights up.

The program begins.

1

1

E

E

Important : 

At the end of the drying cycle, remember to clean the drying filter 

(refer to the

chapter on "EVERYDAY MAINTENANCE OF YOUR APPLIANCE").

Throughout the cycle, the machine
indicates the current phase of the
cycle...

... as well as the estimated time
remaining until the end of the cycle.

Your appliance lets you run a drying cycle straight after a
washing cycle with 

automatic detection of the end of

drying

. This option always uses 

HIGH drying temperature

.

NB:

Results obtained may vary somewhat depending on the

type of laundry load.

To do this:
— Program your 

wash cycle

(see previous pages).

— Sélect the 

“Drying”

option using button 

“Drying”

.

C

C

— Press the “

Start

/Pause” button

. The cycle start.

E

E

— Press the “

Start

/Pause” button

. The cycle start.

NB:

First ensure :

- that the water valve is open.
- that the load has been sufficiently spun (at least 1000 rpm)
and that it does not exceed half a drum.

E

E

— Turn the 

program selector 

to choose your 

“High” 

A

A

or 

“Low” 

drying program according to the type of laun-

dry.
— Select a drying time using the 

button

.

D

D