Соковыжималки Bosch MESM 731M - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
14
en
Adjusting lever / seal for fruit pulp
Adjusting lever /
seal for fruit pulp
X
Fig.
F
– Models with adjusting lever
for seal
The consistency of the juice can be
controlled using the adjusting lever for fruit
pulp.
■
For juice with a lot of fruit pulp, slide the
lever to the right (
Ê
).
■
For juice with less fruit pulp, slide the
lever towards the centre (
É
).
■
To clean/rinse out, remove the juice
drum, turn over and slide the lever to the
stop as shown (
È
).
X
Fig.
G
– Models with seal
The seal for fruit pulp ensures that the juice
has a constant consistency.
■
When making juice or sorbet, the seal
must sit correctly in the aperture for fruit
pulp.
■
To clean/rinse out, remove the juice
drum, turn over and pull out the seal.
Preparation
W
Risk of injury
Do not insert the mains plug until all
preparations for working with the appliance
are complete and all individual parts are
assembled correctly and connected to the
base unit.
Caution!
Never place the juice drum onto the base
unit without the seal for the drive shaft.
Ensure that the seal also sits correctly after
placing it onto the base unit.
Important:
Before re-assembling, check
that the aperture is completely closed by
the seal for fruit pulp.
X
“Adjusting lever /
seal for fruit pulp” see page 14
Preparing to squeeze juice
X
Image sequence
B
1.
Place the base unit onto a stable and
level work surface.
2.
Place the juice drum onto the base
unit. When doing so, align the recesses
on the base of the juice drum with the
counterparts on the base unit (observe
.
markings). The juice drum must sit
flush and firmly on top of the base unit.
3.
Place the rotating brush into the juice
drum.
4.
Place the desired strainer insert piece
(coarse or fine) into the rotating brush
(observe markings
.
).
Important:
Ensure that the aperture and
the notches on the base sit firmly on top of
their counterparts on the juice drum. The
strainer insert piece must not be able to turn
any further.
5.
Place the juicer screw into the strainer
and press down until it sits on top of the
drive shaft.
6.
Place the lid on top (
,
) and turn
it as far as possible in a clockwise
direction (
;
).
Preparing to make sorbet
X
Image sequence
C
1.
Place the base unit onto a stable and
level work surface.
2.
Place the juice drum onto the base
unit. When doing so, align the recesses
on the base of the juice drum with the
counterparts on the base unit (observe
.
markings). The juice drum must sit
flush and firmly on top of the base unit.
3.
Place the sorbet insert piece in the juice
drum (observe markings
.
).
Important:
Ensure that the aperture and
the notches on the base sit firmly on top of
their counterparts on the juice drum. The
sorbet insert piece must not be able to turn
any further.
4.
Place the juicer screw into the sorbet
insert piece and press down until it sits
on top of the drive shaft.
5.
Place the lid on top (
,
) and turn
it as far as possible in a clockwise
direction (
;
).
Характеристики
Остались вопросы?Не нашли свой ответ в руководстве или возникли другие проблемы? Задайте свой вопрос в форме ниже с подробным описанием вашей ситуации, чтобы другие люди и специалисты смогли дать на него ответ. Если вы знаете как решить проблему другого человека, пожалуйста, подскажите ему :)
