STATUS DP550 2142301 - Инструкция по эксплуатации - Страница 3

 4

 2. SAFETY  ADVICE

EN

    • Connect the electric power tool to electricity, using a 16/25 A maximum secure 
      contact protected outlet (220/240V~, 50/60 Hz). We recommend you to attach 
      a residual current circuit-breaker (RCD) that does not exceed 30mA. 

3) PERSONAL SAFETY

    • Hold the power tool on the insulated surfaces while performing any operations, 
      in cases when the cutting tool may directly contact hidden power conductors or 
      may interfere with a power cord.
    • Stay alert, watch what you are doing and use common sense when operating
      a power tool. Do not use a power tool while you are tired or under the influence
      of drugs, alcohol or medication. A moment of inattention while operating power
      tools may result in serious personal injury.
    • Use safety equipment. Always wear eye protection. Safety equipment such as
      dust mask, non-skid safety shoes, hard hat, or hearing protection used for 
      appropriate conditions will reduce personal injuries.
    • Avoid accidental starting. Ensure the switch is in the off position before 
      plugging in. Carrying power tools with your finger on the switch or plugging in 
      power tools that have the switch on invites accidents.
    • Remove any adjusting key or wrench before turning the power tool on.
      A wrench or a key left attached to a rotating part of the power tool may result 
      in personal injury.
    • Do not overreach. Keep proper footing and balance at all times.
      This enables better control of the power tool in unexpected situations.
    • Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
      clothing and gloves away from moving parts. Loose clothes, jewellery or long
      hair can be caught in moving parts.
    • If devices are provided for the connection of dust extraction and collection
      facilities, ensure these are connected and properly used. Use of these devices
      can reduce dust related hazards.

4) POWER TOOL USE AND CARE

    • Do not force the power tool. Use the correct power tool for your application.
      The correct power tool will do the job better and safer at the rate for which it 
      was designed.
    • Do not use the power tool if the switch does not turn it on and off. Any power 
      tool that cannot be controlled with the switch is dangerous and must be 
      repaired.
    • Disconnect the plug from the power source before making any adjustments,  
      changing accessories, or storing power tools. Such preventive safety measures
      reduce the risk of starting the power tool accidentally.
    • Store idle power tools out of the reach of children and do not allow persons 
      unfamiliar with the power tool or these instructions to operate the power tool.
      Power tools are dangerous in the hands of untrained users. 
   • Maintain power tools. Check for misalignment or binding of moving parts, 
     breakage of parts and any other condition that may affect the power tools 
     

 5

EN

     operation. If damaged, have the power tool repaired before use. Many accidents 
     are caused by poorly maintained power tools. 
  •  Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp
     cutting edges are less likely to bind and easier to control.
  • Use the power tool, accessories and tool bits etc., in accordance with these 
     instructions and in the manner intended for the particular type of power tool, 
     taking into account the working conditions and the work to be performed.
     Use of the power tool for operations different from intended could result in a 
     hazardous situation.

5) SERVICE

   • Have your power tool serviced by a qualified repair person using only identical 
     replacement parts. This will ensure that the safety of the power tool is 
     maintained.

Additional safety instructions for your electric drill

   • Do not use the electric power tool with a damaged cable. Do not move the 
     damaged cable, and pull out the power plug if the cable becomes damaged 
     during operation. Damaged cables increase the risk of electric shock.
   • If the replacement of the supply cord is necessary, this has to be done by the 
     manufacturer or his agent in order to avoid a safety hazard.
   • Materials containing asbestos may not be worked on. Fine dust particles can 
     remain in the air, despite the installation of a dust vacuum, and can greatly 
     endanger your health.

   1.  Chuck 
   2.  Left/right rotation switch L/R
   3.  On/off button
   4.  Lock-on button
   

   Danger of injury!

 Before all adjustments and settings: 

   • Turn the machine off.
   • Wait until the machine has come to a complete standstill. 
   • Pull out the power plug.
   

Attachable handle. Never use the impact drill without the attachable handle! 

The attachable handle provides additional support and allows you to work 

   exhaustion-free. The attachable handle is intended for both right-and left-handed 
   persons.

• Loosen the handle of the attachable handle (6) by turning it counter-clockwise. 

    • Guide the drill chuck (1) of the impact drill through the attachable handle. 
    • Then turn the attachable handle to the position which is best for you. 
    • Turn the handle clockwise until the attachable handle sits tightly and can no 
      longer be moved. 
   

  
   
   5.  Changeover switch
   6.  Attachable handle
   7.  Depth gauge
   8.  Rotating button

 3. PARTS  AND  ACCESSORIES

 4. PRIOR  TO  FIRST  USE

PARTS  AND  ACCESSORIES

PRIOR  TO  FIRST  USE