Stanley STDR5510C - Инструкция по эксплуатации - Страница 4

ENGLISH

4

(Original instructions)

4.  Power tool use and care

a.  Do not force the power tool. Use the correct power 

tool for your application. The correct power tool will do 

the job better and safer at the rate for which it was 

designed.

b.  Do not use the power tool if the switch does not turn 

it on and off. Any power tool that cannot be controlled 

with the switch is dangerous and must be repaired.

c.  Disconnect the plug from the power source and/or 

the battery pack from the power tool before making 

any adjustments, changing accessories, or storing 

power tools. Such preventive safety measures reduce 

the risk of starting the power tool accidentally.

d.  Store idle power tools out of the reach of children 

and do not allow persons unfamiliar with the power 

tool or these instructions to operate the power tool. 

Power tools are dangerous in the hands of untrained 

users.

e.  Maintain power tools. Check for misalignment or 

binding of moving parts, breakage of parts and any 

other condition that may affect the power tools 

operation. If damaged, have the power tool repaired 

before use. Many accidents are caused by poorly 

maintained power tools.

f.  Keep cutting tools sharp and clean. Properly 

maintained cutting tools with sharp cutting edges are 

less likely to bind and are easier to control.

g.  Use the power tool, accessories and tool bits etc. in 

accordance with these instructions, taking into 

account the working conditions and the work to be 

performed. Use of the power tool for operations different 

from those intended could result in a hazardous 

situation.

5. Service

a.  Have your power tool serviced by a qualified repair 

person using only identical replacement parts. This 

will ensure that the safety of the power tool is 

maintained.

Additional power tool safety warnings

Warning! Drill safety warnings

•  Wear ear protectors when impact drilling. Exposure 

to noise can cause hearing loss.

•  Use auxiliary handle(s), if supplied with the tool. 

Loss of control can cause personal injury.

•  Hold power tool by insulated gripping surfaces, 

when performing an operation where the cutting 

accessory may contact hidden wiring or its own 

cord. Cutting accessory contacting a "live" wire may 

make exposed metal parts of the power tool "live" and 

could give the operator an electric shock.

•  Use clamps or another practical way to secure and 

support the workpiece to a stable platform. Holding the 

work by hand or against your body leaves it unstable and 

may lead to loss of control.

•  Before drilling into walls, floors or ceilings, check for the 

location of wiring and pipes.

•  Avoid touching the tip of a drill bit just after drilling, as it 

may be hot.

•  This tool is not intended for use by persons(including 

children) with reduced physical, sensory or mental 

capabilities, or lack of experience and knowledge, unless 

they have been given supervision or instruction 

concerning use of the appliance by a person responsible 

for their safety. Children should be supervised to ensure 

that they do not play with the appliance.

•  The intended use is described in this instruction manual. 

The use of any accessory or attachment or performance 

of any operation with this tool other than those 

recommended in this instruction manual may present a 

risk of personal injury and/or damage to property.

Read 

Instructions 

Manual
Use Eye 

Protection
Use Ear 

Protection

V ........   Volts         
A ........  Amperes

Hz .......  Hertz
W ........  Watts
min .....  minutes

.....  Alternating  

Current

.....  Direct  

Current 

n

0

  .......  No-Load 

Speed

 ......  Class II

Construction

....  Earthing 

Terminal

....  Safety Alert

Symbol

.../min..  Revolutions 

or Recipro-

cation per 

minute

Labels on tool

The label on your tool may include the following symbols:

Position of date barcode

The Date Code, which also includes the year of 

manufacture, is printed into the housing.

Example:

2014 XX JN

             Year of manufacturing