Ryobi ONE+ R18PD3-225S 5133003345 - Инструкция по эксплуатации - Страница 3

1

 English 

|

EN

FR

DE

ES

IT

NL

PT

DA

SV

FI

NO

RU

PL

CS

HU

RO

LV

LT

ET

HR

SL

SK

BG

UK

TR

EL

Safety, performance, and dependability have been given 
top priority in the design of your percussion drill.

INTENDED USE

The percussion drill is intended to be used only by adults 
who have read and understood the instructions and 
warnings in this manual, and can be considered responsible 
for their actions.

The percussion drill is intended to be used in drilling into 
various materials, including wood, metal, and plastic using 
a drill bit having a shank diameter of less than 13 mm. 

When in impact mode, the percussion drill can be used in 
drilling masonry and similar materials. When in screwdriving 
mode, the percussion drill can be used in driving screws.

Do not use the product in any way other than those stated 
for intended use.

 WARNING

Read all safety warnings and all instructions.

 Failure 

to follow the warnings and instructions may result in 
electric shock, 

fi

 re and/or serious injury.

Save all warnings and instruction for future reference.

PERCUSSION DRILL SAFETY WARNINGS

■

Wear ear protectors when impact drilling. 

Exposure 

to noise can cause hearing loss.

■

Use auxiliary handle(s), if supplied with the tool. 

Loss of control can cause personal injury.

■

Hold power tool by insulated gripping surfaces, 
when performing an operation where the cutting 
accessory may contact hidden wiring. 

Cutting 

accessory contacting a “live” wire may make exposed 
metal parts of the power tool “live” and could give the 
operator an electric shock.

■

Hold power tool by insulated gripping surfaces, 
when performing an operation where the fastener 
may contact hidden wiring.

 Fasteners contacting a 

“live” wire may make exposed metal parts of the power 
tool “live” and could give the operator an electric shock.

■

Do not operate on materials (e.g., asbestos) that 
present a health hazard.

■

Switch off the product immediately if the bit stalls. Do 
not switch on the product again while the bit is stalled, 
as doing so could trigger a sudden recoil with a high 
reactive force. Determine why the bit stalled and rectify 
this, paying heed to the safety instructions.
The possible causes may be:

–

it is tilted in the workpiece

–

it has pierced the workpiece

–

the product is overloaded

■

Sawdust and splinters must not be removed while the 

product is running.

■

When working in walls, ceilings, or floors, avoid hitting 
electrical cables and gas or water pipes.

■

Secure your workpiece with a clamping device.

TRANSPORTING LITHIUM BATTERIES

Transport the battery in accordance with local and national 
provisions and regulations.

Follow all special requirements on packaging and labelling 
when transporting batteries by a third party. Ensure that 
no batteries can come in contact with other batteries 
or conductive materials while in transport by protecting 
exposed connectors with insulating, non-conductive caps 
or tape. Do not transport batteries that are cracked or 
leaking. Check with the forwarding company for further 
advice.

RESIDUAL RISKS

Even when the product is used as prescribed, it is still 
impossible to completely eliminate certain residual risk 
factors. The operator should pay particular and additional 
attention to these points in order to reduce the risk of 
serious personal injury.

■

Injury to hearing - Wear suitable ear protection and limit 
exposure.

■

Injury to sight - Wear protective eye shields or goggles 
when using the product.

■

Injury caused by vibration - Limit exposure and follow 
the instructions on risk reduction in this manual.

■

Electric shock after contact with hidden wires - Hold the 
product only by insulated surfaces.

■

Respiratory injury from dust created by operating the 
product - Wear suitable protection depending on type 
of dust.

RISK REDUCTION

It has been reported that vibrations from handheld tools 
may contribute to a condition called Raynaud’s Syndrome 
in certain individuals. Symptoms may include tingling, 
numbness and blanching of the 

fi

 ngers, usually apparent 

upon exposure to cold. Hereditary factors, exposure to 
cold and dampness, diet, smoking and work practices 
are all thought to contribute to the development of these 
symptoms. There are measures that can be taken by the 
operator to possibly reduce the effects of vibration:

■

Keep your body warm in cold weather. When operating 
the unit wear gloves to keep the hands and wrists 
warm. It is reported that cold weather is a major factor 
contributing to Raynaud’s Syndrome.

■

After each period of operation, exercise to increase 
blood circulation.

■

Take frequent work breaks. Limit the amount of 
exposure per day.