Metabo SSD 18 LT 200 BL 602397840 - Инструкция по эксплуатации - Страница 11

ENGLISH

en

11

2) Stepless adjustment of the tightening torque:
The speed and tightening torque can be adjusted 

steplessly in any torque setting by pressing the 

trigger (5) firmly or lightly, thus adapting to working 

conditions. 

Recommendation: 

determine the correct setting 

by carrying out trial screwdriving. 

6.5 Changing SSD screwdriving bits

Inserting screwdriving bit: 

Slide locking sleeve  

(3) forward and insert screwdriving bit as far as the 

stop. Release locking sleeve (3) . 

Pull on the screwdriver bit to check that it is 

correctly seated.

Removing screwdriving bit: 

Slide locking sleeve  

(3) forward and remove screwdriving bit. 

Only use screwdriving bits with such plug-in 

ends:

The screwdriving bit used must match the 

screw.
Damaged screwdriving bits must not be used.

6.6 Change screwdriving bit for SSW ...

Inserting screwdriving bit:

 Fit the tool on the 

square attachment (1) until the limit stop.

Removing screwdriving bit:

 Pull the tool from the 

square attachment (1).

The screwdriving bit used must match the 

screw.
Damaged screwdriving bits must not be used.

Mount the machine on the screw, ensuring it is 

aligned straight. 
The screwdriving process consists of 2 parts: 

insert 

screw

 and 

tighten screw with the impact mechanism.

The tightening torque depends on the impact 

duration.

With an impact duration of approx. 5 seconds, the 

maximum tightening torque has been reached.
The torque curve depends on the type of 

application:
With a hard screwdriving application (screw-

couplings in hard material such as metal), maximum 

tightening torque is already reached after a short 

impact duration (a).
With a soft screwdriving application (screw-

couplings in soft material such as wood), a longer 

impact duration (b) is required.
Recommendation: determine the correct impact 

duration by carrying out trial screwdriving. 

Caution!

 For 

small screws 

the maximum torque 

can be reached already after 

0.5 seconds impact duration.
- This is why the duration of the screwdriving 

process must be monitored exactly. 

- Set a (8) suitable tightening torque using the 

button (see chapter 6.4).

- Adjust the tightening torque by pressing firmly or 

lightly on the trigger (5), ensuring that the screw is 

not damaged or that the screw head does not tear 

off.

Use only original Metabo or CAS (Cordless Alliance 

System) battery packs and accessories.
Use only accessories that fulfil the requirements 

and specifications listed in these operating 

instructions.
See page 4.

A Chargers

B Battery packs with different capacities

Use only battery packs with voltage suitable for 

your power tool.

C Screwdriving bits

For a complete range of accessories, see 

www.metabo.com or the catalogue.

Repairs to electrical tools must ONLY be 

carried out by qualified electricians! 

Contact your local Metabo representative if you 

have Metabo power tools requiring repairs. For 

addresses see www.metabo.com.
You can download a list of spare parts from 

www.metabo.com.

Observe national regulations on environmentally 

compatible disposal and on the recycling of disused 

machines, packaging and accessories.
Battery packs may not be disposed of with regular 

waste. Return faulty or used battery packs to your 

Metabo dealer!
Do not allow battery packs to come into contact with 

water!

Only for EU countries: never dispose of 

power tools in your household waste! 

According to European Directive 2012/19/EU 

on Waste from Electric and Electronic Equipment 

and implementation in national law, used power 

tools must be collected separately and recycled in 

7. Use

9,5 mm (3/8“)

8. Accessories

9. Repairs

10. Environmental Protection