Metabo SBEV 1100-2 S 600784500 - Инструкция по эксплуатации - Страница 15

ENGLISH

en

15

-

Caution! The tool is not yet fully tightened!

Keep turning the sleeve (

it must "click" when 

turning

) until it cannot be turned any further - 

only 

now

 is the tool

 safely

 clamped.

With a soft tool shank, retightening may be required 

after a short period of operation.

8.10 Tool change, geared chuck (4) 

Fig. K

8.11 Unscrew the chuck (when driving screws 

without the chuck or for use with attach-

ments) 

Fig. L, M, or N

Note for Fig. M, N:

 Release by tapping lightly with a 

rubber hammer, as shown, and unscrew.

Note:

 If a bit clamping bush (order no. 6.31281) is 

attached, the screwdriver bit inserted in the 

hexagon socket of the spindle is held in place.

Keyless chuck cleaning:

After prolonged use hold the chuck vertically, with 

the opening facing down, and fully open and close it 

several times. The dust collected falls from the 

opening. The application of cleaning spray to the 

jaws and jaw openings at regular intervals is recom-

mended.

Electronic signal display (10):

Rapid flashing - restart protection

(SBEV 1300-2, SBEV 1300-2 S, SBEV 1100-2 S, 

SBE 1000-2)

When power is restored after a power failure, the 

machine - which is still switched on - will not start for 

safety reasons. Switch machine on and off again.
Slow flashing - carbon brushes worn

(SBEV 1300-2, SBEV 1300-2 S, SBEV 1100-2 S)

The carbon brushes are almost completely worn. If 

the brushes are completely worn, the machine 

switches off automatically. Have the brushes 

replaced by an authorized service centre.
Permanently lit - overload 

(SBEV 1300-2, SBEV 1300-2 S, SBEV 1100-2 S)

If the machine is subject to long periods of contin-

uous overloading, the power input of the machine is 

limited. This prevents the further unauthorized 

heating of the motor.

Run the machine in idling until it cools down and the 

electronic signal display switches off.

Use only genuine Metabo accessories.
Use only accessories which fulfil the requirements 

and specifications listed in these operating instruc-

tions. 
Fit accessories securely. Secure the machine if it is 

operated in a bracket. Loss of control can cause 

personal injury.
For a complete range of accessories, see 

www.metabo.com or the main catalogue.

Repairs to electrical tools must be carried out by 

qualified electricians ONLY! 
If you have Metabo electrical tools that require 

repairs, please contact your Metabo service centre. 

For addresses see www.metabo.com.
You can download spare parts lists from 

www.metabo.com.

Observe national regulations on environmentally 

compatible disposal and on the recycling of disused 

machines, packaging and accessories.

Only for EU countries: Never dispose of 

power tools in your household waste! In 

accordance with European Guideline 2002/

96/EC on used electronic and electric equipment 

and its implementation in national legal systems, 

used power tools must be collected separately and 

handed in for environmentally compatible recycling.

Fig. O. 

We reserve the right to make technical 

improvements.
P

1

= Rated  input

P

2

= Power output

n

1

*

= No-load speed

n

2

*

= Load  speed

max. dia. =Max. solid drill diameter

s max = Max. impact rate

b

= Chuck capacity

G

= Spindle  thread

H

= Spindle with hexagon socket

m

= Weight

D

= D=Collar diameter

Measured values determined in conformity with 

EN 60745.

Machine in protection class II

~

Alternating current

The technical specifications quoted are subject to 

tolerances (in compliance with the relevant valid 

standards).

* Energy-rich, high-frequency interference can cause 

fluctuations in speed. The fluctuations disappear, 

however, as soon as the interference fades away.

Emission values

Using these values, you can estimate the emis-

sions from this power tool and compare these with 

the values emitted by other power tools. The actual 

values may be higher or lower, depending on the 

particular application and the condition of the tool or 

power tool. In estimating the values, you should also 

include work breaks and periods of low use. Based 

on the estimated emission values, specify protective 

measures for the user - for example, any organisa-

tional steps that must be put in place. 
Vibration total value (vector sum of three directions) 

determined in accordance with EN 60745:

9. Cleaning, Maintenance

10. Troubleshooting

11. Accessories

12. Repairs

13. Environmental Protection

14. Technical Specifications