Metabo BS 18 LTX Impuls T03470 - Инструкция по эксплуатации - Страница 13

ENGLISH 

en

13

and has no influence on the function or the 

service life of the machine.

7.8 Keyless chuck

Fig. H

With a soft tool shank, retightening may be required 

after a short period of operation.

Notes on machines with the designation SB...:

1. The ratchet sound which can possibly be heard 

after opening the drill chuck is functional and is 

switched off by a reverse rotation of the sleeve.

2. Clamping tool:

Turn sleeve (1) in direction "GRIP, ZU" until the 

noticeable mechanical resistance has been 

overcome.

Caution! The chuck is not yet fully tight-

ened!

 Keep turning the sleeve (

it must "click" 

when turning)

) until it cannot be turned any 

further - 

only now

 is the tool

 safely

 clamped. 

Cleaning:

 From time to time, hold the machine 

vertically with the keyless chuck facing 

downwards and turn the sleeve fully in direction 

"GRIP, ZU" and then turn fully in direction 

"AUF, RELEASE". The dust collected falls from 

the keyless chuck.

7.9 Unscrewing chuck

Fig. I

Employ the same procedure when attaching the 

chuck, except in reverse order.

7.10 Chuck with quick bit change system (for 

BS 14.4 LTX Quick, BS 18 LTX Quick) 

Fig. J

To remove: 

Push the interlock ring forward (a), 

advance and pull off the chuck (b).

To mount: 

Push the interlock ring forward and 

move the chuck as far as the limit stop on the drill 

spindle.

7.11 Attaching the belt hook (depending on 

machine features) / bit depot (depending 

on machine features 

Fig. K

Attach the belt hook to the left (8), as shown.

Attach the bit depot to the right (7), as shown.

8.1 The machine's multifunctional monitoring 

system

If the machine switches off automatically, the 

machine electronics have activated automatic 

protection mode. A warning signal sounds (contin-

uous beeping). The beeping stops after a maximum 

of 30 seconds or when the trigger  (15) is released.

In spite of this protective function, overloading 

is still possible with certain applications and 

can result in damage to the machine.

Causes and remedies:

1.

Battery pack almost empty

Fig. A, B 

(The 

electronics protect the battery pack against 

damage through total discharge).

If one LED is flashing (11), the battery pack is 

almost flat. If necessary, press the  (10) button 

and check the LEDs  (11) to see the charge 

level. If the battery pack is almost flat, it must be 

recharged.

2. Long continuous overloading of the machine will 

activate the 

temperature cut-out

.

Leave the machine or battery pack to cool. 
Note: If the battery pack feels very warm, the 

pack will cool more quickly in an "AIR COOLED" 

charger. 
Note: The machine will cool more quickly if you 

operate it at idling speed.

3. Metabo 

safety shutdown

: The machine was 

SWITCHED OFF automatically. If the slew rate 

of the current is too high (for example, if the 

machine suddenly seizes or kickback occurs), 

the machine switches off. Switch off the machine 

at the trigger (15). Switch it on again and 

continue to work as normal. Try to prevent the 

machine from seizing.

Switch off the machine at the trigger (15). Then 

continue working as normal. Try to prevent the 

machine from seizing.

8.2

Note:

The LED lamp (14) switches off automatically after 

a specific time.
To activate the electronic functions: press the 

trigger (15).

Only use original Metabo battery packs and Metabo 

accessories.
Use only accessories that fulfil the requirements 

and specifications listed in these operating instruc-

tions.
Fit accessories securely. Secure the machine if it is 

operated in a bracket. Loss of control can cause 

personal injury.
For a complete range of accessories, see 

www.metabo.com or the main catalogue.

Repairs to electrical tools must be carried out 

by qualified electricians ONLY! 

If you have Metabo electrical tools that require 

repairs, please contact your Metabo service centre. 

For addresses see www.metabo.com.
You can download spare parts lists from 

www.metabo.com.

Do not allow battery packs to come into contact with 

water!

To protect the environment, do not dispose of 

power tools or battery packs in household 

waste. Observe national regulations on 

separated collection and recycling of disused 

machines, packaging and accessories.

8. Troubleshooting

9. Accessories

10. Repairs

11. Environmental Protection