Metabo BS 18 LTX BL Quick 602197500 - Инструкция по эксплуатации - Страница 14

ENGLISH 

en

13

7.11 Attaching the belt hook (depending on 

machine features) / bit depot (depending 

on machine features 

Fig. K

Attach the belt hook to the left (8), as shown.
Attach the bit depot to the right (7), as shown.

8.1

The machine's multifunctional monitoring 

system

If the machine switches off automatically, the 
machine electronics have activated automatic 

protection mode. A warning signal sounds (contin-
uous beeping). The beeping stops after a maximum 
of 30 seconds or when the trigger  (15) is released.

In spite of this protective function, overloading 
is still possible with certain applications and 

can result in damage to the machine.

Causes and remedies:

1.

Battery pack almost empty

Fig. A, B 

(The 

electronics protect the battery pack against 
damage through total discharge).
If one LED is flashing (11), the battery pack is 
almost flat. If necessary, press the  (10) button 
and check the LEDs  (11) to see the charge 
level. If the battery pack is almost flat, it must be 
recharged.

2. Long continuous overloading of the machine will 

activate the 

temperature cut-out

.

Leave the machine or battery pack to cool. 
Note: If the battery pack feels very warm, the 
pack will cool more quickly in an "AIR COOLED" 
charger. 
Note: The machine will cool more quickly if you 
operate it at idling speed.

3. Metabo 

safety shutdown

: The machine was 

SWITCHED OFF automatically. If the slew rate 
of the current is too high (for example, if the 
machine suddenly seizes or kickback occurs), 
the machine switches off. Switch off the machine 
at the trigger (15). Switch it on again and 
continue to work as normal. Try to prevent the 
machine from seizing.

Switch off the machine at the trigger (15). Then 
continue working as normal. Try to prevent the 
machine from seizing.

8.2

Note:

The LED lamp (14) switches off automatically after 
a specific time.
To activate the electronic functions: press the 
trigger (15).

Use only genuine Metabo accessories.
Use only accessories that fulfil the requirements 
and specifications listed in these operating instruc-
tions.

Fit accessories securely. Secure the machine if it is 
operated in a bracket. Loss of control can cause 
personal injury.
For a complete range of accessories, see 
www.metabo.com or the main catalogue.

Repairs to electrical tools must be carried out 
by qualified electricians ONLY! 

If you have Metabo electrical tools that require 
repairs, please contact your Metabo service centre. 
For addresses see www.metabo.com.
You can download spare parts lists from 
www.metabo.com.

Do not allow battery packs to come into contact with 
water!

To protect the environment, do not dispose of 
power tools or battery packs in household 
waste. Observe national regulations on 

separated collection and recycling of disused 
machines, packaging and accessories.
Before disposal, discharge the battery pack in the 
power tool. Prevent the contacts from short-
circuiting (e. g. by protecting them with adhesive 
tape).

Fig. L. 

We reserve the right to make technical 

improvements.
U

=

Voltage of battery pack

n

0

=

No-load speed

Tightening torque for screwing:
M

1

=

Soft screwing application (wood)

M

2

=

Pulse  torque

M

3

=

Hard screwing application (metal)

M

4

=

Adjustable torque

Max. drill diameter:
D

1 max

=

in steel

D

2 max

=

in softwood

D

3 max

=

in concrete

s

=

Max.  impact  rate

m

=

Weight (with smallest battery pack)

G

=

Spindle  thread

D

 max

=

Chuck clamping range

Measured values determined in conformity with 
EN 60745.

Direct current

The technical specifications quoted are subject to 
tolerances (in compliance with the relevant valid 
standards).

Emission values

Using these values, you can estimate the 

emissions from this power tool and compare these 
with the values emitted by other power tools. The 
actual values may be higher or lower, depending on 
the particular application and the condition of the 

8. Troubleshooting

9. Accessories

10. Repairs

11. Environmental Protection

12. Technical specifications