Makita DDA450ZK - Инструкция по эксплуатации - Страница 4

4 ENGLISH

ENGLISH (Original instructions)

SPECIFICATIONS

Model:

DDA450

Gear speed

High

Low

Drilling capacities

Steel

13 mm

Wood

Auger bit: 38 mm 

Self-feed bit: 50 mm 

Hole saw: 101 mm

Auger bit: 38 mm 

Self-feed bit: 65 mm 

Hole saw: 127 mm

No load speed

0 - 1,400 min

-1

0 - 450 min

-1

Overall length (With battery cartridge BL1860B)

434 mm

Rated voltage

D.C. 18 V

Net weight

3.2 - 3.5 kg

• 

Due to our continuing program of research and development, the specifications herein are subject to change without notice.

• 

Specifications may differ from country to country.

• 

The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi

-

est combination, according to EPTA-Procedure 01/2014, are shown in the table.

Applicable battery cartridge and charger

Battery cartridge

BL1815N / BL1820B / BL1830B / BL1840B / BL1850B / BL1860B

Charger

DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF / 

DC18SH

• 

Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.

WARNING:

Only use the battery cartridges and chargers listed above.

 Use of any other battery cartridges 

and chargers may cause injury and/or fire.

Intended use

The tool is intended for drilling in wood, metal and plastic.

Noise

The typical A-weighted noise level determined accord-

ing to EN62841-2-1:

Sound pressure level (L

pA

) : 83 dB(A)

Sound power level (L

WA

) : 94 dB (A)

Uncertainty (K) : 3 dB(A)

NOTE:

 The declared noise emission value(s) has been 

measured in accordance with a standard test method 

and may be used for comparing one tool with another.

NOTE:

 The declared noise emission value(s) may 

also be used in a preliminary assessment of exposure.

WARNING:

Wear ear protection.

WARNING:

The noise emission during actual 

use of the power tool can differ from the declared 

value(s) depending on the ways in which the tool is 

used especially what kind of workpiece is processed.

WARNING:

Be sure to identify safety measures 

to protect the operator that are based on an estima-

tion of exposure in the actual conditions of use (tak-

ing account of all parts of the operating cycle such 

as the times when the tool is switched off and when 

it is running idle in addition to the trigger time).

Vibration

The vibration total value (tri-axial vector sum) deter-

mined according to EN62841-2-1:

Work mode: drilling into metal

Vibration emission (a

h,D

) : 2.5 m/s

2

 or less

Uncertainty (K) : 1.5 m/s

2

NOTE:

 The declared vibration total value(s) has been 

measured in accordance with a standard test method 

and may be used for comparing one tool with another.

NOTE:

 The declared vibration total value(s) may also 

be used in a preliminary assessment of exposure.

WARNING:

The vibration emission during actual 

use of the power tool can differ from the declared val

-

ue(s) depending on the ways in which the tool is used 

especially what kind of workpiece is processed.

WARNING:

Be sure to identify safety measures 

to protect the operator that are based on an estima-

tion of exposure in the actual conditions of use (tak-

ing account of all parts of the operating cycle such 

as the times when the tool is switched off and when 

it is running idle in addition to the trigger time).

EC Declaration of Conformity

For European countries only

The EC declaration of conformity is included as Annex A 

to this instruction manual.