Шуруповерты FERM PMM1006 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
4
EN
• For long hair, wear hair protection. Work only
with closely fitting clothes.
• Secure the vessel with the mixed substance
against moving on the floor.
• Always direct backwards the flexible lead from
the tool. The flexible lead should not be
exerted by tensile stress and should not lie on
or pass over sharp edges.
• Use the supplementary handle.
• Consider possible reaction torque.
• Wear ear and eye protection.
Immediately switch off the machine when:
• Excessive sparking of the carbon brushes and
verticiliosis in the collector.
• Interruption of the mains plug, mains lead or
mains lead damage.
• Defect switch
• Smoke or stench of scorched isolation
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
Always check that the power supply
corresponds to the voltage on the rating
plate.
Class ll machine. Your machine is double
insulated; therefore no earthwire is
required.
Replacing cables or plugs
Immediately throw away old cables or plugs
when they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in the
wall outlet.
Using extension cables
Only use an approved extension cable suitable
for the power input of the machine. The minimum
conductor size is 1,5 mm
2
. When using a cable
reel always unwind the reel completely.
3. ASSEMBLY
Assembling the two-part whisk
Fig. A
1. Screw the Whisk shaft (9A) onto the Whisk
paddle (9B)
2. Tighten both parts securely
Replacing the whisk
Fig. A
Before assembly, always switch off the
machine and remove the mains plug from
the mains.
Use only whisks conform the specified diameter.
Always use a whisk that is suitable for the material
to be mixed/stirred. Using an unsuitable mixer bar
can unnecessarily overload both the machine and
yourself.
Mounting the whisk
1.
Screw the assembled whisk into the tool holder
(5) in clockwise direction as far as possible.
2. Tighten the whisk into the tool holder using
the supplied spanners. To do so, hold the tool
holder (5) using one of the supplied spanners,
and use the second spanner to tighten the
assembled whisk.
Removing the whisk
1. Loosen the assembled whisk using the
supplied spanners. To do so, hold the tool
holder (5) using one of the supplied spanners,
and use the second spanner to loosen the
assembled whisk.
2. Unscrew the whisk from the tool holder (5) in
anti-clockwise direction.
4. USE
Improper use may damage the instrument.
Observe therefore these instructions:
• Use a tool up to the specified diameter.
• Load the tool in such a way that the speed would
not drop considerably or that it would stop.
Check if the data on the rating plate correspond
with the actual mains vol tage.
Instrument scheduled for 230 V can be plugged to
220 V/240 V mains.
The ON/OFF switch
• To switch on the tool, press and hold the on/off
switch (1).
• If you release the on/off switch, the tool will be
switched off.
Switch locking mechanism
You can lock the on/off switch by pressing the
on/off switch (1) and then button (2). The switch
lock can be released by briefly pressing the on/off
switch.
