Fein BOZ 32-4 M 72025160000 - Инструкция по эксплуатации - Страница 16

16

en

Do not rivet or screw any name-plates or signs onto the 
power tool. 

If the insulation is damaged, protection 

against an electric shock will be ineffective. Adhesive 
labels are recommended.

Do not use accessories which are not specifically 
designed and recommended by the power tool manufac-
turer. 

Safe operation is not ensured merely because an 

accessory fits your power tool.

Clean the ventilation openings on the power tool at regu-
lar intervals using non-metal tools. 

The blower of the 

motor draws dust into the housing. An excessive accu-
mulation of metallic dust can cause an electrical hazard.

Before putting into operation, check the mains connec-
tion and the mains plug for damage.

Recommendation: The tool should always be supplied 
with power via a residual current device (RCD) with a 
rated current of 30 mA or less.

Hand/arm vibrations

The vibration emission level given in this information 
sheet has been measured in accordance with a standard-
ised test given in EN 60745 and may be used to compare 
one tool with another. It may be used for a preliminary 
assessment of exposure.
The declared vibration emission level represents the 
main applications of the tool. However, if the tool is used 
for different applications, with different accessories or 
poorly maintained, the vibration emission may differ. 
This may significantly increase the exposure level over 
the total working period.
An estimation of the level of exposure to vibration 
should also take into account the times when the tool is 
switched off or when it is running but not actually doing 
the job. This may significantly reduce the exposure level 
over the total working period.
Identify additional safety measures to protect the opera-
tor from the effects of vibration such as: maintain the tool 
and the accessories, keep the hands warm, organisation 
of work patterns.

Handling hazardous dusts

For work procedures with this power tool where mate-
rial is removed, dusts develop that can be hazardous to 
one’s health.
Contact with or inhaling some dust types, e. g. asbestos 
and asbestos-containing materials, lead-containing coat-
ings, metal, some wood types, minerals, silicate particles 
from materials containing stone, paint solvents, wood 
preservatives, antifouling paints for vessels, can trigger 
allergic reactions to the operator or bystanders and/or 
lead to respiratory infections, cancer, birth defects or 
other reproductive harm. The risk from inhaling dusts 
depends on the exposition. Use dust extraction matched 
appropriately for the developing dust, as well as personal 
protective equipment and provide for good ventilation of 
the workplace. Leave the processing of asbestos-contain-
ing materials to specialists.
Wood and light-metal dust, hot mixtures of grinding dust 
and chemical materials can self-ignite under unfavourable 
conditions or cause an explosion. Avoid sparking in the 
direction of the dust collector as well as overheating of 

the power tool and the materials being sanded, empty the 
dust collector/container in time, observe the material 
manufacturer’s working instructions, as well as the rele-
vant regulations in your country for the materials being 
worked.

Operating Instructions.

Degrease the output spindle and the inside cone of the 
drill chuck before mounting.
When the application tool continuously blocks or is sub-
ject to overload, the motor stops automatically. Restart 
the motor again.
Change the gear setting or the rotation direction only 
after the motor has come to a complete stop.
For stationary use in a drill stand, remove the switched 
off power tool from the drill stand every 50 operating 
hours while at normal running temperature. Then, turn 
the machine around by 180 °  to achieve uniform lubrica-
tion.

Repair and customer service.

When working metal under extreme operat-
ing conditions, it is possible for conductive 
dust to settle in the interior of the power tool. 

The total insulation of the power tool can be impaired. 
Blow out the interior of the power tool via the ventila-
tion slots frequently with dry and oil-free compressed air, 
and connect a residual current device (RCD) on the line 
side.
If the supply cord of this power tool is damaged, it must 
be replaced by a specially prepared cord available through 
the FEIN customer service centre.
The current spares parts list for this power tool can be 
found on our website at www.fein.com.

If required, you can change the following parts yourself:

Drill chuck, auxiliary handle, application tools

Warranty and liability.

The warranty for the product is valid in accordance with 
the legal regulations in the country where it is marketed. 
In addition, FEIN also provides a guarantee in accordance 
with the FEIN manufacturer’s warranty declaration.
The delivery scope of your power tool may include only 
a part of the accessories described or shown in this 
Instruction Manual.

Declaration of conformity.

FEIN declares itself solely responsible for this product 
conforming with the relevant provisions given on the last 
page of this Instruction Manual.
Technical documents at: C. & E. Fein GmbH, C-D1_IA, 
D-73529 Schwäbisch Gmünd

Environmental protection, disposal.

Packaging, worn out power tools and accessories should 
be sorted for environmental-friendly recycling.