Fein AWBP 10 Select до 10 мм 71050462000 - Инструкция по эксплуатации - Страница 18

18

en

Use only intact original FEIN batteries that are intended 
for your power tool. 

When working with and charging 

incorrect, damaged, repaired or reconditioned batteries, 
imitations or other brands, there is danger of fire and/or 
explosion.

Follow the safety warnings in the operating instructions 
of the battery charger.

Hand/arm vibrations

The vibration emission level given in this information 
sheet has been measured in accordance with a standard-
ised test given in EN 60745 and may be used to compare 
one tool with another. It may be used for a preliminary 
assessment of exposure.
The declared vibration emission level represents the 
main applications of the tool. However, if the tool is used 
for different applications, with different accessories or 
poorly maintained, the vibration emission may differ. 
This may significantly increase the exposure level over 
the total working period.
An estimation of the level of exposure to vibration 
should also take into account the times when the tool is 
switched off or when it is running but not actually doing 
the job. This may significantly reduce the exposure level 
over the total working period.
Identify additional safety measures to protect the opera-
tor from the effects of vibration such as: maintain the tool 
and the accessories, keep the hands warm, organisation 
of work patterns.

Handling hazardous dusts

For work procedures with this power tool where mate-
rial is removed, dusts develop that can be hazardous to 
one’s health.
Contact with or inhaling some dust types, e. g. asbestos 
and asbestos-containing materials, lead-containing coat-
ings, metal, some wood types, minerals, silicate particles 
from materials containing stone, paint solvents, wood 
preservatives, antifouling paints for vessels, can trigger 
allergic reactions to the operator or bystanders and/or 
lead to respiratory infections, cancer, birth defects or 
other reproductive harm. The risk from inhaling dusts 
depends on the exposition. Use dust extraction matched 
appropriately for the developing dust, as well as personal 
protective equipment and provide for good ventilation of 
the workplace. Leave the processing of asbestos-contain-
ing materials to specialists.
Wood and light-metal dust, hot mixtures of sanding dust 
and chemical materials can self-ignite under unfavourable 
conditions or cause an explosion. Avoid sparking in the 
direction of the dust collector as well as overheating of the 
power tool and the materials being sanded, empty the dust 
collector/container in time, observe the material manufac-
turer’s working instructions, as well as the relevant regula-
tions in your country for the materials being worked.

Operating Instructions.

Change the gear setting or the rotation direction only 
after the motor has come to a complete stop.
To avoid accidental starting, e. g., during transport, set 
the rotation selector switch to the centre position.
When overheated, the machine runs with short, low-
power impulses. Allow the machine to cool down at no-
load speed.

For stationary use in a drill stand, remove the switched off 
power tool from the drill stand every 50 operating hours 
while at normal running temperature. Then, turn the 
machine around by 180 °  to achieve uniform lubrication.

AWBP10: 

Degrease the output spindle and the inside 

cone of the drill chuck before mounting.

Handling the battery.

Operate and charge the battery only within the battery 
operating-temperature range of 0 °C – 45 °C (32 °F –
113 °F). At the beginning of the charging procedure, the 
battery temperature must be within the battery operat-
ing-temperature range.

The real percentage of the battery charge condition is 
only indicated when the power tool motor is stopped.
The electronics automatically switch off the motor prior 
to the battery being deep discharged.

Repair and customer service.

When working metal under extreme operat-
ing conditions, it is possible for conductive 
dust to settle in the interior of the power tool. 

Blow out the interior of the power tool via the ventila-
tion slots frequently with dry and oil-free compressed air. 
The current spare parts list for this power tool can be 
found in the Internet at www.fein.com.

If required, you can change the following parts yourself:

Drill chuck, auxiliary handle, application tools, battery

Warranty and liability.

The warranty for the product is valid in accordance with 
the legal regulations in the country where it is marketed. 
In addition, FEIN also provides a guarantee in accordance 
with the FEIN manufacturer’s warranty declaration.
The delivery scope of your power tool may include only 
a part of the accessories described or shown in this 
Instruction Manual.

Declaration of conformity.

FEIN declares itself solely responsible for this product 
conforming with the relevant provisions given on the last 
page of this Instruction Manual.
Technical documents at: C. & E. Fein GmbH, C-DB_IA, 
D-73529 Schwäbisch Gmünd

Environmental protection, disposal.

Packaging, worn out power tools and accessories should 
be sorted for environmental-friendly recycling.
Dispose of batteries only when discharged.
For batteries that are not completely discharged, insulate 
the terminals with tape as a protective measure against 
short-circuiting.

LED indicator Meaning

Activity

1 – 4 green 
LED

Percentage of 
charge condition

Operation

Continuous 
red light

Battery is almost 
empty

Charge battery

Red flashing 
light

Battery is not 
ready for opera-
tion

Bring the battery into 
the battery operat-
ing-temperature 
range, then charge

OBJ_BUCH-0000000067-002.book  Page 18  Friday, May 23, 2014  12:29 PM