Fein AWBP 10 Select до 10 мм 71050462000 - Инструкция по эксплуатации - Страница 17

17

en

For your safety.

Read all safety warnings and all 
instructions.

 Failure to follow the 

warnings and instructions may result in electric shock, 
fire and/or serious injury.

Save all warnings and instructions for future reference.

Do not use this power tool before you have thor-
oughly read and completely understood this 
Instruction Manual and the enclosed “General 

Safety Instructions” (document number 
3 41 30 054 06 1). The documents mentioned should be 
kept for later use and enclosed with the power tool, 
should it be passed on or sold.
Please also observe the relevant national industrial safety 
regulations.

Intended use of the power tool:

hand-held drill for drilling in metal, wood, plastic, ceram-
ics, and for tapping in weather-protected environments 
using the application tools and accessories recommended 
by FEIN.

Special safety instructions.

Use auxiliary handle(s), if supplied with the tool. 

Loss of 

control can cause personal injury.

Hold power tool by the insulated gripping surfaces, when 
performing an operation where the cutting accessory 
may contact hidden wiring. 

Cutting accessory contacting 

a “live” wire may make exposed metal parts of the power 
tool “live” and could give the operator an electric shock.

Beware of any concealed electric cables, gas or water 
conduits. 

Check the working area before commencing 

work, e. g. with a metal detector.

Secure the work piece firmly. 

A work piece that is 

gripped tightly in a clamping device or vice, is more 
secure than if held by hand.

Hold the power tool firmly. 

High reaction torque can 

briefly occur.

Do not direct the power tool against yourself, other per-
sons or animals. 

Danger of injury from sharp or hot 

application tools.

Do not rivet or screw any name-plates or signs onto the 
power tool. 

If the insulation is damaged, protection 

against an electric shock will be ineffective. Adhesive 
labels are recommended.

Do not use accessories which are not specifically 
designed and recommended by the power tool manufac-
turer. 

Safe operation is not ensured merely because an 

accessory fits your power tool.

Clean the ventilation openings on the power tool at regu-
lar intervals using non-metal tools. 

The blower of the 

motor draws dust into the housing. An excessive accu-
mulation of metallic dust can cause an electrical hazard.

Use and handling of the battery (battery pack).

To avoid hazardous situations such as burns, fire, explo-
sion, skin injuries, and other injuries when handling the 
battery, observe the following instructions:

Batteries must not be disassembled, opened or reduced 
in size. Do not subject batteries to mechanical impact or 
shock. 

Hazardous vapours and fluid can escape in case of 

damage and improper use of the battery. The vapours can 
irritate the respiratory system. Liquid ejected from the 
battery may cause skin irritations or burns.

When battery fluid from a damaged battery has come into 
contact with objects close by, check the respective com-
ponents, clean them or replace them as required.

Keep the battery away from heat and fire. Do not store the 
battery in direct sunlight.

Do not remove the battery from its original packaging 
until it is going to be used.

Before any work on the machine itself, remove the bat-
tery from the power tool. 

If the power tool accidentally 

starts, there is danger of injury.

Remove the battery only when the power tool is switched 
off.

Keep the battery away from children.

Keep the battery clean and protect it against moisture 
and water. 

Clean contaminated battery terminals and 

power tool connections with a dry, clean cloth.

mm

mm

d1 = Clamping range of drill chuck
d2 = Shank size of drilling shaft
d3 = Collar diameter

kg

kg

Weight according to EPTA-Procedure 01/2003

L

pA

dB

dB

Sound pressure level

L

wA

dB

dB

Sound power level

L

pCpeak

dB

dB

Peak sound pressure level

K...

Uncertainty

m/s

2

m/s

2

Vibrational emission value according to 
EN 60745 (vector sum of three directions)

h,D

m/s

2

m/s

2

Mean vibrational value for drilling in metal

m, s, kg, A, mm, V, 
W, Hz, N, °C, dB, 
min, m/s

2

m, s, kg, A, mm, V, 
W, Hz, N, °C, dB, 
min, m/s

2

Basic and derived units of measurement from 
the international system of units 

SI

.

Character

Unit of measurement, 
international

Unit of measurement, 
national

Explanation

WARNING

OBJ_BUCH-0000000067-002.book  Page 17  Friday, May 23, 2014  12:29 PM